Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Hi,
What should i do after i load mesh app in " github.com/.../nRF51-ble-bcast-mesh" adress?i have two board
When i download the app,why doesnt advertising exist.i cant...
hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
During developpement of project on nRF52810, we used the nRF52DK PCA10040.
Since we wanted to use P0.9 and P0.10 (to limit differences between eval-board and real board...
I need to develop a ble advertising scanner with these requirements:
- capture at least 10 beacon advertisments (Eddystone TLM) continuously
- advertising interval of...
Hi,
I recently got the nRF51 Dongle for testing of a board with bluetooth interface. I am trying to get this dongle installed in Linux.
I found this link for the SDK...
Hi
I have a project need to be customized advertising frequency and scan in specific frequency
It means nrf52832 could broadcast at specific frequency and scanner also...
Dear Nordic Support,
I am using nRF52840 and BLE SDK v15.2. I want to control my nRF52840 through both UART CLI and BLE CLI so I try and read example: nRF5_SDK_15.2.0_9412b96...
Hello
I have a firmware with Softdevice S132 for NRF52 consists of main application (0x1F000 len:0x56000 ) and Bootloader (0x75000 len:0x9000). What I'm trying to do is...
Dear Nordic Team,
I am using a nRF52832 module purchased from Adafruit ( https://www.adafruit.com/product/3406 ) and I would like to connect it with another device with...
Hi there
First I tell you what I'm, trying to do...
I want to made a connection between a robot and a pc. Over this connection I want to program the robot with new software...
Hi,
I'm using nRF52832 SDK 14.2.0 s132 dfu, softdevice 5.0.0.
And i'm trying to update SD + BL + APP to SDK 15.3.0, softdevice 6.1.1.
When i update pakage by nRF connect...
Hi,
I am trying to upload HEX files to a nrf52832 (on a Sparkfun Breakout board) with a nRF52 DK. The problem is nRF Connect Programmer don't recognize them.
I installed...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flash the image. I am using ‘ble_app_blinky’.
In sdk_config.h, BLE_ADVERTISING_ENABLED is not...
Hi, I'm currently in trouble with the sd_flash_write function. I've already a library using this function running on the nRF52832 with the S132 softdevice. But when a tries...
I want to use TWI to read the sensor data. When using the software TWI, I found that the communication takes a long time, which will greatly increase the battery consumption...
Hey,
I'm trying to put the nRF9160 into System Off mode and am getting a bus fault error when writing to the REGULATORS module. This is the error output:
***** BUS...
