Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Hello, I studied on example\ble_peripheral\ble_app_ancs_c in SDK15.2.0 with board PCA10040. After paring and bonding sucessfully with my iPhone, I reset PCA10040 with Button...
Hi
I am looking to use a pre-certified modules for meshing.
However BLE Mesh have some rather big limitations for the size of network/bandwidth i have in mind and I have...
Hello,
I am searching the way of decoding the motion raw data from thingy 52.
Especially, for the accelerometer values.
In the app, I get the next value:
FAFF...
I read the post here. This post was used nRF52 DK (PCA10040) . I have the nRF52 DK (PCA10056) card. nfc applications in sdk always nRF52 DK (PCA10040). How do I run nfc applications...
Hi,
This error occurs when I write below command for OTA_DFU demo:
cmd : exe keys generate private.key Error:
ImportError: cannot import name 'DIGCF_PRESENT' from...
Hey,
I am working on mesh program, I am trying to send mesh message periodically for every 5 secs when i press a button in nRf52 DK. The message is being send for 3 or 4...
Hi,
I am using nrf52840 module with a kit that i built by myself. The kit is working because i am able to flash and debug without problems.
I am using Segger embedded...
Hi,
Is it possible to advertize and scan only on the 2M PHY and w/o using at all the 1M PHY on nRF52840/S140 system ?
The actual system is running fine if we use the 1M...
Good day!
I purchased the nRF24L01 Evolution Kit, but:
1. The driver and software that comes with the board, only under Windows XP. Are there drivers and software for...
Sorry in advance if this is an FAQ or maybe two
Situation is this - for regulatory reasons, production/release software here is built using a known version of arm-gcc, and...
I'm using scannig with whitelist on nRF52840 Dongle SDK V15.2 (usbd_ble_uart_freertos example)
when BLE_GAP_EVT_ADV_REPORT is called scanning stops, So it can scan just...
I am working on matching an antenna to the nrf52832 QFN package. I am looking at the reference design, which has a 30 mil wide trace. I believe that is supposed to be 50 ohms...
I have an application (key fob) that needs to wake up on a button press. Scan and connect to a specific BLE device, then send one byte of data and disconnect and turn off...
Hello, I have a question about using PPI with a SPI transfer.
I’m using a NRF52832 custom board with the Softdevice. I’m reading sensor data every 20ms via TWI and sampling...
