Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Hi,
What should i do after i load mesh app in " github.com/.../nRF51-ble-bcast-mesh" adress?i have two board
When i download the app,why doesnt advertising exist.i cant...
Hello,
In an application I am using NRF52832 IC as central. Before uploading code in every board, I need to change the device name and compile. This process is consuming...
Hi Nordic Team,
I'm having some trouble with using the nrf_calendar with the softdevice...
I'm using the SDK V12.3.0 and softdevice s130 V2.0.1 and the exemple ble_central...
I read a few questions there were related to this, none that i encountered seem to give me an answer.
I am using SDK15.1 nRF52
I am NOT using dynamic allocation, I need...
Hi,
I want to connect NRF51822 wit NRF51 development kit over the air i-e. Development Kit would work as server (look for available client and connect with it and then send...
Hi,
I am using nrf51422 dk board in my project. so i need to use Bluetooth in my project. Could you plz tell me the which version of SDK do i need to use for this Bluetooth...
Hello to everyone.
I'm working with chip nRF52832 (PCA10040) and Mesh 3.1. I'm trying to connect a HC-05 Bluetooth/Serial Module using its serial pins (Rx/Tx) to the default...
Hi,
I am using SDK 15.3 and NRF52840 Preview DK
I have a requirement where I have to glow one of 3 LEDs R-G-B (each connected to one gpio pin) for 1 second and turn...
I'm using nrf52840 to develop a remote control using BLE long range.
We use two nrf52840 : on inside the remote and another in the system to control. The remote is used...
Hi,
I've done a lot of searching and Googling and could not find a proper answer for the life of me, so I'm posting again here to try to find answers. I must have looked...
I want to use internal temperature sensor in the example, "peripheral\temperature" on our software but there is the problem that we met when applying on board internal temperature...
I'm using nRF51DK and created 2 app_timers (based on LFCLK) that are running on 32.768kHz crystal, one for kernel timing (10ms) and one for real time clock (every second)...
Hi,
For some reasons, I would like to write my own application for updating the firmware, something like NRFUTIL application.
I wrote it and everything is working fine...
Hello,
I am trying the ble_app_cts_c_pca10040_s132 (current time service client). Under the conditions described below, ultimately a SoftDevice call to sd_ble_gap_device_identities_set...
I am attempting to integrate examples/peripheral/flash_fstorage into my project (SDK 14.1.0).
When calling nrf_fstorage_write I get NRF_ERROR_INVALID_LENGTH in response...
