Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
Hey, I am working on the proximity application on nrf51 DK. How can I get the bsp_event_handler to get triggered on a button multi press (such as pressing button 1 twice rapidly...
Hi,
Do you have support for mobility in Cat-M on your nRF9160? This is usually done in RRC connected, but i'm wondering if you are able to support it in eDRX as well?...
Hello;
We are developing a project. And there must be three features in our project.
1) Should scan and transmit beacon at the sametime
2) Chip should read and write...
How can i read advertisement and not connect? I would like to do some checks on the advertising data within BLE event BLE_GAP_EVT_ADV_REPORT and then decide if i want to manually...
I am trying to transmit a modulated carrier with a high duty cycle but it does not work
the same command works with the default duty setting (50%).
The cli freezes when...
VUSB current consumption of the NRF52840: We have a setup where the 5V supply to this pin has very limited current capability.
What is the maximum current which can go into...
The Problem: HardFault within sd_softdevice_enable. With HardFault breakpoint enabled, the debugger halts at address 0x8C8. With this breakpoint disabled, breakpoints after...
I having trouble setting power level above +4 dbm in my app based on the example "ble_app_beacon" using the PCA10059 nRF52840 dongle. I have updated the main.c with the following...
Hi, i'm designing a device which is based on nrf52832 chip and i need to add two IC on my board, the first one is the MAX8856 to charge the battery of my device and the second...
I want to execute timer interrupt at a certain interval, like 1sec or 5 sec.
I measured an actual interval of voltage change with oscilloscope, but the actual interval is...
Hello
i have nrf 51822 beacon and i need to setup beacon that he send out data and i scan it without connecting-read brcst data.
i scan microchip 4870 and other beacon...
What is the best method for attempting to recover from a stuck TWI bus after init?
I am currently initializing the TWI instance with .clear_bus_init=true but this only...
I just finished upgrading the SDK version from v14.2 to v15.3, one thing I'm having trouble with is that after secure buttonless DFU finishes the call to `sd_softdevice_disable...
I'm testing this with SDK 15.2 on an NRF52832, with SD132.
I'm trying to implement error handling for FDS, but some cases are not clear to me how to deal with them.
Am...
We are working with DK nrf 52840 and the sdk mesh 3.0, BT sdk version is15.2 (dimming server example).
We noticed that when nordic app(nrf mesh - android) send a generic...
