I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Hi, I was confused about the behavior of GPIOTE Handler module。I defined a handler(gpiote_event_handler) and I hope when the GPIO Pin(0.14) is changed from high to low or...
I use the example usbd_ble_uart with SDK_15.3.0. I need to send any byte received from the terminal via BLE. Do not wait until the buffer is full or the end of line character...
Hi,
I am trying to combine the usbd (hid mouse) example with the uart central example to run on the nRF52840 dongle. I am having a lot of problems and am not really sure...
I have some colleagues that are working on a project where they want to use the nRF52 as a general purpose IO processor alongside providing an BLE interface to a host Linux...
I installed SDK 15.3.0 build 59ac345 and started working though the DFU secure boot loader example. In the 15.3.0 documentation it says
Setup
You can find the source code...
Hello
We are using custom board which has two chip configuration for BLE stack. Main MCU runs the Zephyr Host only BT stack in peripheral mode.This is supposed to be GATT...
I am trying to compile the SPI example in SDK 15.2.0 for nrf52810. I am getting a compiler error in SES on nrfx_uart.c:
I modified the project according to the SDK documentation...
Dear all,
Is this possible to flip a switch on the board to get nRF9160 IOs at 3.3v rather than 1.8v ? I have a LoRa module that requires TTL 3.3v UART signals, and it...
Hello,
I believe I have found a possible race condition in experimental_task_manager / task_manager.c, task_events_wait().
The race occurs if a task calls task_events_wait...
Hello, I'm working with an example of ble_app_uart with SofDev132. I have modified the code a bit but I still use the nrf_pwr_mgmt_run function. The power consumption is 2...
hello, i am complete beginner to this field of MCU, i never worked on nordic MCUs. i am able to program the dk-board using the usb cable and readymade hex file provided in...
Hi,
I'd like to enable paring/bonding for a minute only when a button is pressed. So I need to disable pairing. I've learned that it should be done with
in "ble_evt_handler...
Hi,
I would like to have two different twi managers. One with TWI0 and one with TWI1. But if I try to enable them I get an error:
sdk_config.h:1810:22: error: unable to...
