I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Hi,
We have used nRF51822 QFAA H10 in our product for a long time but the latest order was fulfilled with H30-devices and now our production test fails.
The test step...
Dear all,
I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 and S132 SoftDevice v6.1.0 to do some tests . But now I encounter the disconnect reason 0x22...
Hi,
I'm using nus for the sensor works with uart 57600 baud rate.
Few munites later connection is broken. I don't know why.
Can anybody know this issue?
Waiting...
Just test SDK14.20 serial DFU demo project on Nordic PCA10040 board by USB serial.
Got below exception. Any clue for it please?
Thanks.
C:\gxf\nrfutil\nordic>..\nrfutil...
Hello,
I want to modify the NRF logging module to include the line number where the log was originated.
In the past I created a wrapper macro that called NRF_LOG_INFO...
Hi all,
I am using nRF82532 board. This board TX,RX(P0.06,p.0.08) pins connected with QUECTEL module in ZEPHYR sdk platform . Please forgive me for these basic doubts. ...
HI,
I want to work nRF52 thingy with segger embedded studio.
Is there any example code to compile and run the Project file for nRF52_thingy?
Which sdk need to use SDK13...
Hello,
I'm trying to autoconnect my device to my phone using nrf Connect app. I connect to my board selecting autoconnect flag, then insert my passkey and devices are correctly...
I programmed the 15.2 sdk (ble_app_eddystone_pca10040_s132.hex) to my 52832 radioland module.
I can see that it is identified as an eddystone with URL of nordic -
But...
Hi,
I want to make device that can switch between central and peripheral role on NRF52810.
I am using S132 and nrf SDK 14.2.0.
Can I change the roles with button and...
Hi Team,
Trying to recover my nrf9160 DK, don't know what I did wrong, please help.
IDE: SES Nordic edition V4.14
Hardware: nRF9160 DK, Program/Debug to nRF91 module...
Please Help,
I want to remove the firmware from traditional beacons and deploy NORDIC FW instead so that i can deploy SDK for mesh on the beacons after that and use it to...
I have some code that runs on the 52832 DK and I'd like to migrate it to the 52840 dongle, but I'm not sure what I need to do to accomplish that. I changed the memory locations...
Hi
In nRF52832 datasheet page 17, it informed low drive and low frequency on 10 GPIO.
Could you define what max value of low driver and low frequency?
Thanks.
Atl...
