Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
In previous SDKs (e.g. version 15.0) the following macros were defined in app_util.h
As described in this post these needed to be modified to support more than 15 connections...
I am trying to do the segger development for the 9160 lte ble gateway. When I do the setup info for segger I keep getting a popup saying it can't find the .emproject file...
Hi
I'm working my way through learning how develop BLE Services and Characteristics for an NRF52840. I'm using the 'ble_app_template' example from the SDK (version 15.2...
Hi,
I have the following lines:
NRF_LOG_ERROR ( "This is an ERROR message." );
NRF_LOG_WARNING ( "This is a WARNING message." );
NRF_LOG_DEBUG ( "This is a DEBUG...
I am inquiring about an issue with the SPIM communication. I am reading the who am i sensor of an MPU9250 and it reads 0x71, as it should most of the time but not always....
uVision V5.26.2.0
Error #541: 'NordicSemiconductor::Device:Startup:8.24.1' component is missing (previously found in pack 'NordicSemiconductor.nRF_DeviceFamilyPack.8.24...
I have a complete implementation of OTA DFU where iOS app performs a DFU to a nRF based BT Device. Now i am implementing a fix for the situation where:
During DFU, if...
Hi,
I am currently having issues compiling the thingy52-mesh-provisioning demo from github with cmake. The Readme talks about using SES to compile it, which works fine,...
Hello, I have read multiple postings on this problem about how you have to "forget" the MCU on your android to reconnect through Bluetooth. This does not fix the problem at...
Hello,
I am having an issue where the nRF52840 dongle does not properly reset. I'd appreciate it anyone can help.
I was evaluating the DFU options, and erased the IC in...
Hi,
I am currently using the nRF52832 and I just recently realized that it does not have USB capabilities. I am building a custom board with this chip and I want to use...
My environment: SDK 15.2, SD 6.1.0, SES 4.12
I can build and run the BLE blinky example on the nRF 52832 DK with no problems. I tested LED on/off by writing to the BLE characteristic...
All,
We have an issue with the data transfer rate between a device that uses a nRF52480 (Rigado-340).
We are sending a number of data chunks, approximately 400, where...
Hello,
Now, I am merging my UART code with the TWI sensor example (I use SDK 13). Now my error after compiling the code is:
In file included from ../../../../../../components...
Hello, i recently used a gateway to sensor example and am unable to revert back to factory program of nrf9160 DK.
I toggled the switch 5 to nrf52840 and flashed the first...
