I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
HI ALL,
I want to create a static library in the application layer, but this library will contain nrf related header files, which will cause cmake to not compile properly...
We have a custom board based on the nRF52805 and we're seeing some odd behaviors in debugging / testing that we're trying to nail down. Two questions:
The INFO.VARIANT...
When I use the J-link programming program, the following happens to the J-flash connection chip
SEGGER J-Link Commander V7.67d (Compiled Jul 5 2022 16:15:35) DLL version...
Hello, my custom board is using pin 09 to communicate through uart. I want to check that uart is working on this custom board. First, I tried to create a simple uart application...
I am using NCS v2.8.0.
After successfully running the headset example with one gateway, one left channel receiver and one right channel receiver am trying to get the Auracast...
I spent quite some time trying to understand why I was getting random network disconnect after a totally fine CEREG notification, like in this log:
It turns out that inside...
Dear Nordic:
Light bulb project support 52840DK, can light bulb project support 52840 dongle? I have not found dongle option in l ight bulb boards folder, only find nrf52840dk_nrf52840...
Hello. consisting of nrf7002 + nrf5340, I'm going to do battery management and power management of a circuit that operates up to a small coin electric motor at npm1100, and...
Hi,
I am encountering an issue with the BLE connection on my nRF5340 DK. When I attempt to connect the device to my PC, the pairing process takes a significant amount of...
Hi,
I am implementing a BLE central that is based on ble_app_uart example using nRF52833 with a soft device version 7.2.0.
I have noticed that a single packet download...
Toolchain v2.70, SDK v2.7.0, VS Code, Windows
I am trying to enable the watchdog in my application, and I can successfully locate the device node and add a timeout, but...
Hi,
I am trying to figure out a way to update the toolchain and SDK for an nRF Connect for VS Code installed on an offline machine, without much success.
From https:/...
Hello,
I am working with the NRF9151 DK on DECT NR+ and I want to change the subcarrier scaling factor and subslot value in the hello_dect example. However, I am not sure...
NRF Connect SDK (v2.8.0), VS Code, NRF52840
Hi, while reading the Zigbee documentation I saw the following note:
"Support for Zigbee R22 has been deprecated in nRF Connect...
I am simply trying to build the hello world (and blinky, results are the same) with NRF-SDK 1.8.0 - it's based on Zephyr 2.7, which is the LTS release.
Target board is 5340...
