Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Hi,
What should i do after i load mesh app in " github.com/.../nRF51-ble-bcast-mesh" adress?i have two board
When i download the app,why doesnt advertising exist.i cant...
hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using the CLI interface through USB and UART, and I am wondering if there are any innate methods for checking the validity of the data being sent and received via the...
hi Nordic support team,
I cannot re-flash firmware for nrf52840 after ram off is implemented.
I recheck with other chip like nrf52833, it have the same result: \althrough...
I understand, it is possible to add variables to a section of ram, that will not be initialized (zeroed) at boot (see for example: https://github.com/nrfconnect/sdk-zephyr...
Hello,
I want to create my own board from the nrf52840. I am planning to copy the schematics given only taking into account what I need. I went through the schematics and...
Hello,
I am using the nRF51822 with SDK v9.0.0, SoftDevice S110, and the DFU bootloader v8.1.0.
For certain reasons, I want to reserve one page of the 'app data' for shared...
Hi Support Team
If a center role and a peripheral role in one nRF52840 at the same time，can the center role use code PHY and the peripheral role use 1M PHY？Many thanks.
Hi,
I need to read the data from an acceleration sensor. I tried with a custom program of mine to simulate some data, but it is delaying too much.
I tried reducing the...
Hi,
Iam using nRF5340 DK and nRF Connect SDK V.2.6.1.
Iam following the link
FOTA over BLE
In this one until 5th step it worked fine and while doing 6th step it is...
Hi,
I have purchased some Thingy:91 devices. They are HW version 1.6.1 but I cannot find the documentation for that on your website. It seems that the latest available is...
Hello,
I am using nrf5340 Audio DK board. In that board I have flashed a sample firmware of Unicast Gateway.
This firmware is suppose to scan the advertisement and establish...
Hi there,
I am writing code to set my BLE PHY throughput from 1M to 2M when my device establishes a connection; my code works when I connect to my nRF52840 dongle from a...
Hi ,
I'm in Nrf52840Dongle Getting the PCM data in the following way, I want to print him to the serial port and then import it through Audacity to make sure I have the...
Hi,
I'm trying to understand how I exactly can differentiate between CODED S=2 and S=8. I've experimented with the BLE fundamentals Lesson 3, Exercise 2 and set the PHY...
Hi,
I am using VS code for nordic 9160dk, and when create a new application - copy a sample and choose the Blinky sample / Asset Tracker v2 application , and build configuration...
Hi
I am using nRF52832 , SDK17, S132, reading a device ID which should be 0x67, I am reading 0x33, than 0x80 ,so it seems to be that the MISO window is getting offseted...
