hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hello!
We are on the process of implementing our own desktop program to run DFU over BLE, similar to how the nRF Connect application does it. We are using SDK 17.1.0 in...
Hi ,
I would like to know if we can use 2 PPK's in such way to measure both direction.
As you can see in the diagram , the current can flow to the battery or can flow...
The bluetooth program refers to app_ble_uart. Bluetooth uses nRF52840. I use stm32 MCU to transmit data through UART. The baud rate is 460800 for transmission. The UART transmission...
I am using nrfConnect for Visual Studio Code 2.6.1 and I am being asked what version of Zephyr I am using when diagnosing a problem in a Zephyr forum. There has to be some...
Hi
Seems like all new nRF DKs shipped with nRF5340 as interface mcu have limited speed on Debug Out.
nrfjprog -r --clockspeed 646 Applying system reset. Run. nrfjprog...
I need to send a JWT to a non-nordic server. They ask for a small struct to be encoded and sent as a string in a larger MQTT message. For example:
That struct is encoded...
I have flashed the light_ctrl hex file in nrf52840 dongle. Flashing Have been completed sueccessfully for provisioning in nrf mesh application its not showing in the network...
Hello,
For a Uni Project I want to measure the current of the Nordic Thingy:91 and visualize it. Therefore i bought the Power Profiler Kit 2. But i dont know how to connect...
So when changing the hci_icp.conf settings to have the configuration below, i get "CMake Error at C:/ncs/v2.6.1/zephyr/cmake/modules/kconfig.cmake:358 (message):" plus the...
My device is peripheral. I added a few lines before the advertisement start in main(). The whole project is in main and simply advertise and get connected and bonded.
...
I want to configure the ESB and nRF21540 chips on the NRF21540-DK. In order to compare the signal gain, I used the nRF52832-DK and burned the Bluetooth routine (without any...
Hello,
I have a project working on Nora B1, which I am testing on nrf5340DK. It is based on the Peripheral UART Sample, programmed with nfr Connect SDK v1.9.1. Now I need...
Hello,
This is probably a dumb question but, I'm having issues with an initial prototype for a product that has been given. The hardware engineer (me) designed and got...
Quick Start can see the board - but says 'Not supported yet'
Load the programmer and select my board: The log looks like this:
19:07:18.801
Initialising nrfutil...
