I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
I am currently migrating from ncs 2.5.0 to 2.7.0 and am trying to move to using sysbuild instead of child / parent image. I have an out of tree flash driver that currently...
I am looking for some simple slave and master samples to run on my dk's nut cant find any. in the intermediate course there is the master slave talking with the sensor but...
Hi,
We have a blue tooth mesh application similar to light and light-switch setup.
server nodes: light
client nodes: light-switch
We expand the light-switch node to...
Hello Nordic team,
I followed the official guide to add a custom sensor cluster to my Matter application. Everything built and flashed successfully, and the application...
When will the nRF9151 Hardware Design Guidelines document be available?
We are currently leveraging information in the nRF9161 Hardware Design Guidelines document in the...
Hi,
I've recently brought up the Matter Test Harness on a Raspberry Pi following the instructions in the CERT tool repository ( https://github.com/project-chip/certification...
I am building a nrf52840 custom board and testing the ble_app_blink_pca10056_s140 example from segger I have a 32MHz crystal and a 32.768khz crystal And I added the following...
Hello everyone,
I’m facing an issue with step-by-step debugging in VSCode using the ARM GCC compiler with an nRF52811 microcontroller and Nordic’s SDK 17.1.
Here are the...
I've got a custom board using an nRF52832. I'm using the P0.06/P0.08 as the TX/RX pins for UART comms, but don't need the P0.05/P0.07 pins for CTS/RTS. Is there anyway I can...
Hello. I am currently working on a Mesh Network using the Nordic Thingy53 board. As far as I understand, the Mesh protocol developed by Nordic already has encryption, obfuscation...
Hello
When following the guidline of a new way to extend boards , VSCode "Add Build Configuration" is blank. Am I doing something wrong or this is not yet supported by...
I am Creating a custom model for my application using the chat client example. My project is based on checking the battery percentage of a device using this model. So what...
Hello,
In a project using the NRF52832. Softdevice SDK 19.1.0 and Segger IDE, I inizialize the BLE for having NUS and DFU services actives. I try to reproduce the code here...
I have four of these devices. nRF5340 Audio DK.
I would like to use them as follows. Is there a way to set them up?
Device A: source
Device B: sink left
Device C:...
Hi,
I would like to ask when using zephyr's k_timer it uses a clock from LFCLK, then it can be generated in the following three ways:
32.768 kHz RC oscillator (LFRC) 32...
