I'm using S332 0.9.1 with freertos. nRF52.
BLE and ANT are both active. I would like to run the ANT continuos wave (CW) test after a specific trigger (a command over a console...
I want to encrypt advertisements using aes-ccm peripheral present on the nrf51 board. I am not using softdevice, instead I am generating my own packets and transmitting them...
Currently, it using the I2S at nRF52832.
I want to play the wave file,But can not play well.
So, I ask you for a check because there is the following question.
[Question...
We love the radio range of the Nordic bluetooth chips. I am looking to see if anyone is developing a long-range bluetooth pendant or wearable? if so, I interested in perhaps...
I'm trying to read 8 adc channels using SPI, but then if I dont put some nrf_delay_ms the MISO return nothing and the CS is being driven low by default, high or a period of...
Does rbc_mesh_value_enable() API is designed for ? and how should I use it? and what does its parameter handle mean? Is it has the same meanning as the parameter handle of...
I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
Hello,
I have added DFU capabilities to my NRF54L15 project using:
CONFIG_NCS_SAMPLE_MCUMGR_BT_OTA_DFU =y
and
SB_CONFIG_PARTITION_MANAGER =y
SB_CONFIG_BOOTLOADER_MCUBOOT...
Hello DevZone Community,
I wanted to share a unique hardware-in-the-loop implementation using the Power Profiler Kit II (PPK2). While the industry is heavily focused on...
I am designing an FPGA to have a SPI slave port connected to the nRF5340 SPIM4 master running at 32 MHz. But the setup and hold times for this configuration are missing from...
I have an application which is not able to talk with my gas gauge device when the TI EV2400 can. Looking at the waveforms all look the same except for the Zephyr code has...
our current network provider says that they have a restriction on their sim profile so that the mtu should be less than 1430. however things like pdn_dynamic_params_get()...
Is there a recommended way to access the USB data lines from the J3 connector of the nPM1300EK? I would like to be able to charge the battery and also provide a USB mass storage...
Hi, I am starting to get into the Nordic world and want to design my first pcb with nordic chips. I would like to get a review on my schematics and the pcb. I am mostly interested...
[Corrected 2026-09-11] This post originally attributed an MPU fault to the missing 7c4ea9a9d5. That was wrong — backporting it did not stop the fault, which looks like a separate...
Hello Nordic Support,
I need version-specific troubleshooting advice for an nRF52840 DK, PCA10056 hardware v3.0.3 (label 2026.16), with the nRF5340 interface MCU. I have...
nPM1300 LOADSW1/LDO1 quiescent current issue — XIAO nRF54LM20A Sense
Status: unresolved as of 2026-08-27. Written to summarize the investigation for external reference ...
Hi,
I am developing firmware on the nRF93M1 DK and have a question regarding the Wi-Fi location feature. According to the Nordic documentation (Features of nRF93M1 — nRF...
Hello,
we are trying the nRF93M1 DK hw rev. 0.4.0
As suggested, we wanted to build the following sample: https://nrfconnectdocs.nordicsemi.com/ncs/latest/nrf/samples/nrf93m1dk...
Dear Nordic,
As per the RED, article 3.3 www.intertek.com.hk/.../ item (d) radio equipment does not harm the network or its functioning nor misuse network resources, thereby...
