I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
Hi,
I am developing an embedded system that uses Bluetooth communication and would like to manipulate certain Bluetooth characteristics such as TX power and RX sensitivity...
BLE Device
- nRF Connect SDK: v2.0.0
https://github.com/NordicSemiconductor/IOS-DFU-Library
This library doesn't seem to support the new nRF Connect SDK.
Which library...
Until 1.9.0 of NCS, SES was recommended, so it was possible to use OpenOCD from there. With NCS 2.x.x, VCS is recommended, so it's good to use it, but I want to continue using...
Hi,
We have some variables in shared memory. These variables can be accessed directly by both cores, and this is not controlled through IPC.These variables can be accessed...
Hi Nordic Team
Starting Point:
Provisioning of dimming server is done with code from the PB Remote provisioner, working so far.
Publish of model to group is acived similar...
Heyyy guys!
It is possible that I'm doing something wrong, but i'm confused as this was definitely not an issue at some point while i've been working with the 5340.
I...
Included "bsp.h" and "nrf_fstorage.h" still getting these below errors:
undefined refence to `bsp_indication_set'
undefined reference to `nrf_fstorage_init'
undefined...
Our product is using NVS to manage settings in external flash. The normal NVS initialization time is between 1 to 3 seconds at boot. Occasionally I have witnessed 10 to 15...
Target nRF52832(nrf52dk_nrf52832) SDK NCS v1.9.1
Normally OTA works well. I found unexpected assert after OTA is done. Can you please review my assert code with my elf....
I want to make a low power beacon with GPIOTE input which indicates movement and causing a change in the beacon advertisement (e.g. minor value). In order to do that I am...
Hi,
I am using Zephyr's sample code of sensors. Sample code is using wrapper function for device initialization, getting sensor's value etc. But there is no API exposed...
Hello! Just a quick question. I cannot find this file anywhere ` <InstallFolder>\examples\multiprotocol\ble_zigbee\ble_zigbee_dynamic_door_lock_nus`. This is referred to from...
Hi, From some time I'm trying to fix problems with throughput sample. I don't know why, but after setting data len parameter to any value it's constantly sets 27.
uart:...
We are evaluating using GPIOTE In event to trigger SPIM reading by PPI. GPIOTE interrupt will trigger SPIM data transfer. The SPIM CS pin is toggled with PPI too. We use a...
I am using a NRF9160 module using NCS 1.8.
My application is successfully using GNSS, HTTPS, and MQTT. The issue I am currently having is premature wakeup from the POWER...
