I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
Hello, this is Kwonjoon Lee. I have a problem of PC-BLE-Driver (C/C++ library) installation.
I am following installation guide which is written in the https://github.com...
Hi!
When reading the documentation of the I2S peripheral of the nRF52840, I don't see how to stop the transfer after the last data block. Figure 2 only shows how to start...
Hi,
I used the BLE blinky app on a nRF52832DK and it was working nicely.
I am then trying to make it run on a custom board with nRF52832QFAB version mounted.
I see several...
Hi,
I'm hoping someone can help me get faster throughput when doing DFU in nRF Connect Desktop
I'm using the following hardware / software:
- macOS 12.01
- nRF Connect...
On the nrf52840 I have libuarte working.
The part runs on 1Mbps with 2 timers connected in the define.
This all works great for 90% of the time.
When the incoming data...
Hello I'm curently working on a Project where I'm using the nrf52dk board with the nrf52832.
I wanted to change the dimension of the data transfered with my characteristics...
Hi, sdk:ncs v1.7.0
example path:D:\ncs\v1.7.0\zephyr\samples\subsys\usb\hid-cdc
board :nrf5340dk_nrf5340
DK:PCA10095
How to solve this problem?
Thank you for all...
Hi,
Excuse me. How can I modify cmakelist.exe to display file structure in segger Embedded Studio compiler? Now all files are app/libapp.a below. I have a lot of files now...
Hi, My system has 5 nRF52840 peripherals connected to one central device (PC app).
In the peripheral's sdk_config.h there is a macro NRF_SDH_BLE_PERIPHERAL_LINK_COUNT 1...
If download example light_switch on new clear chip nrf52832, that advertising is not done. But after downloading the firmware without mesh, example light_switch will broadcast...
Hi All,
I am using VS code with nrf Connect Extension and nrf Connect SDK 1.7.0 develop nrf5340 application on windows10.
I created a new application from the Hello World...
I combined the BLE UART and SPIS Peripheral example of SDK V17.0.2 to receive 251 bytes of data from a microcontroller using SPIS protocol. The microcontroller sends data...
Hi,
Peripheral : SDK13, nRF52832
Central : SDK16, nRF52832
It is a phenomenon that occurs in the central device.
I have two questions about the secure connection...
I'm using the latest nRFConnect SDK w/ VSCode with a custom board connected to via a J-LINK. When I look at the call stack it only shows the current thread. I can see thread...
I would like to know when each BLE advertising event has ended for possibility stop after specific number of events and to be able to update advertising data between events...
