hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi. We have nRF9160 DK using Serial LTE Modem as standalone modem for CAT-M1 connected with external nRF52 via UART2. We have setup the modem to establish connection to AWS...
I used the nrf52832-QFAA Reference Layout as the base design for the PCB.
The changes I made were:
1.) Added the DS1339 RTC Pin P0.22 will be configured SCL and pin...
Hi,
I am using nRF52840 dongle. The REG_OUT is programmed to 3.3V by default.
I am planning to use Li ion battery at VDDH. When the battery discharges below 3.3V, is there...
I have an issue when i am using an iPhone 8 instead of iPhone 7 , I can use iphone7 to OTA my BLE UART by NRF tool box, but ,when i useing iphone 8 , it does not work, what...
Hi,
Please advise.
I am using (nRF5SDK160098a08e2) , nrf52840 .
This is my code to change name in Runtime not via restart or timeout.
I call the function below every...
I'm trying to sniff BLE communicate data between the devices with nRF51822.
I have connected one device to the selected it with the interface toolbar. But I can't sniff...
Hello, I am using the ISP1507-AX and want to compile the BLE UART Mode Example "ble_app_uart_pca10040_s132" with SEGGER Embedded Studio in order to generate a hex file like...
Hi,
We have been working with nRF52832 and using BLE Mesh in our product. The product is an Access control reader which scans for nearby smartphones over BLE and sends...
Module model: nrf52832
SDK: 15.2
Hi,
I am trying to add custom characteristics to a custom service.
There are two ways that I am aware of:
a. sd_ble_gatts_characteristic_add...
I have a firmware version present SDK 13.1 and S132 SoftDevice v4.0.5 I am trying to do a DFU (just SD+BL first) which now has SDK 16.0 and S113 SoftDevice v7.0.1 But my package...
Hello, I have a issue about flash_manager module.
When I load a program on processor (that has been previously erased) there is a problem with initialization (flash_manager_add...
I'm trying to get a temperature reading from the on-chip temperature sensor on the NRF52832 - I know it is not a very accurate sensor but I still want to use it. I found a...
With IAR (EWARM) 8.50.9 the UART project in the SDK compiles fine.
After upgrading to IAR (EWARM) 9.10.1 or 9.10.2 I get compiler error:
Error[Go029]: Variable "sec_mode...
Hi!
I'm trying to use a precompiled library of TVOC sensor ZMOD4410 in a project based on the azure_iot_hub from Nordic, running it over a nrf9160 board.
This library...
