Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Hi
On my device, after a successful (bonded) connection to a central, if I then turn off BLE on that central, my device moves through fast advertising and slow advertising...
Hi
I am trying to get the SDHC/Disk access with FAT working on the nRF9160 dev platform and Asset_Tracker V1 app
It is shown to be connected on the TRACE connector ...
I have two BC805M EK .
Board 1: when I upload the (LED controlled by reset button) code to it, it works fine.
Board 2: when I upload the LED control code to it, I could...
Hi,
I want to build an application for nRF52840 DK that receives data through BLE from mobile phone (via nRF connect android application) and sends it to another microcontroller...
nrf51822 QFAC have more flash and ram than QFAA, so, is QFAC consume more electric current than QFAA in idle mode and sleep mode? in low-power consumption product，if it's...
Hi,
I want to configure 2 channels of saadc in differential mode as follows:
But when I received data, it seems that only the channel that its channel index is zero...
Hello,
1) In nrf5340 app CPU, there are only 3 timer I can use, timer0, timer1 and time2, is it right?
2) I want to use four timers in my project, to control two SPI...
Hello,
I'm seeing nrfjprog return with error code 33 when I try to program (or erase) an Adafruit Feather nRF52. I'm using an nRF52-DK as a programmer. The feather board...
Hi,
I'm trying to write/read from flash in my app. Reading/writing works until I either:
a) run ant_hrm_rx_start() - then after the call to nrf_fstorage_erase I get "00...
Hello!
I'm from Russia, my name is Anton.
I need a developer kit to research a real-time motion tracking system (RTLS) based on Bluetooth Low Energy, Bluetooth 5.1, Bluetooth...
Привет! Я из России, меня зовут Антон. Мне нужен комплект разработчика для исследования системы отслеживания движения в реальном времени (RTLS) на основе Bluetooth Low Energy...
I am trying to upload an image via BLE DFU, tested on mobile phone and Desktop (Windows) But I receive the following error after all packages have been sent to the device...
Hi,
can nRF52/nRF53 automatically fall back to LDO mode if DCDC enabled in firmware but with bad inductor connection on PCB?
Could re-flash the firmware to disable DCDC...
Hi everyone.
I'm developing a product with nRF5340 and zephyr os. But I found some problems about bluetooth dfu.
Because my application very big. So I can't use defualt...
Hi,
I am evaluating the use of nRF52832/52840 running ZephryOS HCI (Uart or USB) in combination with Bluez/Linux to as central device/gateway. If I were to use the Nordic...
