Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Hi Dear
Good Day!!
I want to know about which clock frequency they are used in nrf5SDK internal or external FREQ, and along with the where can i find the declarations...
Hello,
I am trying to work on an application to transfer BLE characteristic data to an SD card.
I ran the FATFS example on my setup and it works perfectly with the Test...
Dear sir.
I'm an engineering working on circuit design , micom program, and PCB artwork. from korea. My name is Jeong eui-jong.([email protected])
In conclusion,...
Dear Nordic Team,
I am currently using nRF52840 with nRF5 SDK v16.0.0 for developing a prototype of wearable device.
The wearable device should be able to act as
a)...
I'm implementing the full modem firmware update as demonstrated by the sample located at /samples/nrf9160/http_update/full_modem_update.
A bunch of it works. I'm able to...
I try to modify one of the pc-ble-driver examples to work together with my PCA10040 and the Nordic UART Service example in my Qt application, but the application doesn´t discover...
Hello,
I'm currently using SDK v17.0.2 with the NRF52840 on nRF52840-DK Board. After going through the example code of "nrfx_spim" I was able to get up and running. I...
Hi, I am trying to integrate DWS3000 (UWB) APIs, given here to nRF52840 with BLE stack enabled such that my firmware can blink Eddystone packets at the same time when UWB...
The customer requested that pairing be prohibited under certain circumstances, so I called API
sd_ble_gap_sec_params_reply(m_conn_handle, BLE_GAP_SEC_STATUS_PAIRING_NOT_SUPP...
in ~/ncs/zephyr/samples/hello_world/prj.conf or in ~/ncs/zephyr/boards/arm/nrf9160dk_nrf9160/nrf9160dk_nrf9160ns_defconfig
CONFIG_I2C=y
in my nrf9160dk_nrf9160ns.overlay...
Hi,
We are using nrf52833 for measuring angle of arrival. We got IQ samples from the device we need to calculate the phase difference from that IQ sample. please explain...
Hi, we have an application using an nRF52832 without a SD that we want to put into low power / sleep mode to save battery.
What commands should we use to do this and wake...
Hi,
I am using ppi to read some continuous data from a sensor through SPI and i got it working, it reads data in evry 8ms from the sensor through ppi.
but it fails when...
