hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Hi,
I use the app_buton module to handle the buttons. When detecting a button interrupt I call a function that sends data to I2S (using the "app_sched_event_put" function...
hello,
i am using nrf52840 in our customised board and trying to interface it with GDEW0213Z16 2.13 inch display which uses spi communication i have added the necessary...
I'm new to the nRF connect sdk (but have used the previous sdk in the past), and am wondering what the best way to start a new project is? With the old sdk, it was easiest...
Hi,
I'm having "SOFTDEVICE: ASSERTION FAILED" when I set a breakpoint or pause the program to check some variables. That's really annoying, basically making the debugging...
Hi Dev team,
I was trying to build the mqtt_simple sample in the new NCS v1.5.0 and I am getting a build error.
I tried to build other samples as well but was faced...
Currently I am running one of the demo applications and have the nRF power source switch set to Vdd. The measured Vdd is 3.0V. Is it possible to change this to 3.3V? I would...
Hello
Is it posibile to do debug using Segger ES simulator for an example which uses also BLE stack?
More specific I am trying to debug the blinky example found in
...
Custom board, ncs v1.4.0, modem FW v1.2.3, SES v5.10d. The code is based on the Asset Tracker (v1), LTE with PSM, motion-activated GPS, using MQTT to send messages to private...
We are considering the nRF9160 SIP for a product we plan to develop. There is questions around whether we will need to obtain regulatory certification (Starting within U.S...
Hi,
I noticed that if you send AT+CFUN=1 then AT+CFUN=4 more than 30 times in an hour the modem stops registering until the hour passes? Is this by design?
Kind regards...
Hi,
I have built and flashed the "peripheral_uart" example on the nrf52833dk_nrf52833 from nrfconnect sdk v1.5.0. When I build using the prj_minimal.conf file, everything...
Is it possible to manually delete/inject bonding keys when BLE connecting to device with using Nrf52 and pc-ble-driver.py? I would need to execute following scenario:
1...
I have seen a compatibility matrix for nRF52840 SoC at the link below:
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcomp_matrix_nrf52840%2FCOMP%2Fnrf52840%2Fnrf52840_comp_matrix...
