hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi,
I am trying to understand how to enable SPI in blinky application provided by Nordic. My intention is to transfer data between the two Nordic development kit running...
I have advertising in s130 set to BLE_GAP_ADV_TIMEOUT_GENERAL_UNLIMITED. The idea is to advertise until a connection event is received. In reality the user will pull the finger...
Hi ,
1. I learned from Nordic FAE that on the nrf9160 module, 10 minutes after the edrx mode, the nrf9160 module automatically powers off the sim card to save power,
2...
Hello Team,
I want to use scheduler to schedule two tasks i.e task_1 and task_2. The task_1 and task_2 are as follow:
void task_1() { printf("Task 1 ran"); }
void task_2...
Sorry this might be a stupid question.
We are evaluating some modem to develop a IoT device, NRF9160 comes up to our list as its tiny size.
In the design of IoT device...
I wants to use break point in project but when i set break point then 4 or 5 times working after that goes to NRF_BREAKPOINT_COND, I am using nRF52832. so guide me where is...
We are using NRF52840 and we have a watchdog timer connected to reset the Nordic, if needed. What is the minimum and maximum time need to insert a reset on Nordic?
thanks...
I want to transfer sensor data to a raspberry pi using the in-built USB on nrf52840. The example codes have the following classes: CDC_ACM, Audio, HID and Mass storage. I...
Hello,
I am just curious wether there are any specific recommendations or requirements for the package-sizes of capacitors/inductors listed in the BOMs of the nRF52840-reference...
Hello,
I am working with the latest version of nRF52 SDK 13.0.0, when I was implementing my own bootloader application, I tried to start an app timer in my code to invert...
Hi there,
Could you please tell me the exact part number of nRF9160 and nRF52840 on Thingy: 91?
I cannot find the specific information even though I looked through the...
Hi All,
How many nodes can connect to a node in ble mesh network. I go through code in ble mesh, but i did't found the answer.
Can any one please tell me.
Regards
...
We have an application using SDK for Thread 4.1. The application requires sending large custom commands over CLI.
We increased the size of NRF_CLI_CMD_BUFF_SIZE in sdk_config...
Hi, I am using the nRF connect app to test the BLE function on my code. I am able to scan the device and Service UUIDs just fine. However, when I click on the "connect" button...
