hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi,
I'm using NRF52811 to evaluate the direction finding. I have successfully got the phase data, but I found a strange thing:
I did some processing on phase data for...
I am currently testing Optiga Trust X using an NRF52 DK. I am using armgcc as my toolchain.
The example provided by the nRF5 SDK v17.0.0 is a great starting point and I...
Hi,
I am using nrf52810 and a sample SAADC code from the examples folder provided by the manufacturer. I have connected a potentiometer for validating my output values....
A continuation from here: https://devzone.nordicsemi.com/f/nordic-q-a/64842/mesh-pa-lna-problems
If I want to only enable the PA/LNA chip for the mesh stack, but not for...
Dear Nordic Support,
Our product is based on nrf52840/s140 and we have difficulties connecting to it using Huawei P8 Lite while it is fine using other Android or iOS phones...
I have a compiled code and I want only to change the uart pins without compiling the code again
If it is possible to modify only the hex code, how can I find the UART pins...
I am trying to find where to submit bugs against the pc-ble-driver. There are two major bugs I have found
saved CCCDs (in a bonded connection) do not get restored when...
Hello, everyone
I use NRF52840 to configure TWI to operate the sensor, but I don’t understand it.
Can the hardware TWI of 52840 be mapped to any IO?
Or is there a fixed...
Hello!
NRF52832 is used as a central for connecting with phones as peripheral. NUS service is used. Lesc is used too.
SDK 17 SoftDevice S132 V7.0.1
On android phones...
when I use usb to transfer, i fine many datas are lost.Is it because the DMA size is too small?Where can i see the dma size?(In nrf52833/examples/peripheral/usb_cdc_acm )...
I am trying to connect a SPI device to the external connector pins on the nRF9160dk board. I believe I know the name of the SPI device and the pin connections from the device...
Hello
I'm trying to print out several sounds with one buzzer. To do that, I need to be able to change the frequency.
PWM was initialized and reset using code. An attempt...
OS: Linux Ubuntu 18.04
Compiler: Gnu ARM embedded
HW: 2 nrf52840dk boards
NRF SDK: 16.0.0
I am trying to send data using L2CAP CoC. I have looked at the ots example...
Hello,
I am trying to get familiar with the DeviceTree macros and started experimenting ...
So, in the light controller example main.c I replaced this macro
#define...
