I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Hi,
I'm trying to run the gps application off the master branch on the thingy91 and it dies like this:
It's built using the Nordic SES on windows.
Any ideas? ...
Hi all,
I am trying to connect to device with specific UUID. I am not sure what have I managed to do, below are some logs from NRF Log.
Did I connect properly?
I am...
Hello,
I am trying to run the mbdedtls example of random number generator shown here https://tls.mbed.org/kb/how-to/add-a-random-generator
I added MBEDTLS_CONFIG_FILE...
when i change the baud rate to 115200 my uart (Rx and TX) are giving me garbage out put.
so what do i need to change in my code(ble_app_uart example) when i have plan...
Dear Support / forum,
After reading the user and API guides, browsing other posts, and playing around with the ack-payload example, I think I now have a pretty good understanding...
Hi,
I am having a issue with building an application in IDE for nRF9160
Application : Asset tracker
I have been able to build this "problemfree" before, but this morning...
Hi~
I am developing door sensor system using nRF52840.
Currently for power consumption, sensor (nRF52840) is system off(NRF_POWER->SYSTEMOFF=1).
nRF52840 can wake up...
Hi, I have 8 peripheral devices each one has at least one sensor attached to it( peripheral will be nRF52xx), the sensor has a sampling period of 8ms. I will be using android...
Hi,
In BLE mesh v3.1.0 I see a file debug_pins.h. For what these debug pins are used and can I disable it for my custom board?
And one more thing related to PA and LNA...
Hi,
We are currently developing a Sensors/USB/BLE/LTE-M1 product for a customer. The board is equipped with one nRF9160,for cloud communication, and one nRF52840, with a...
Hello, I am using nrf5832 with SDK 15.3.0. I want to filter peripheral device based on mac address. I modified example code "\examples\ble_central\ble_app_blinky_c\pca10040...
I'm facing problem when I want to stop receive task, event EVENT_RXTO came at long time period. 4 to 5 baudrate bytes.
Is trere any documentation where could read time between...
Hello,
I want to develop a data transfer service which has a control characteristic that is used to write commands on the phone app and if the command matches any command...
In our application we have made a connection between two nrf52840 devices. with softdevice 6.1.1
normally we operate in 1Mbit mode and tx power on 8.
if we change from...
Hi,
After sending a few textmessages from the client to a server (8 bytes long approx. 10 messages/sec) i get a mesh assert on the client sometimes:
0> <t: 205648>, app_error_weak...
