hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hello,
I'm trying to use the nrf52840 Dongle on the Raspberry 3B+. I didn't achieve to run an appImage downloaded from your site. When i'm executing the app nothing happens...
My current hardware is based on SoftDevice SD132, v6.0.0 as provided with SDK 15.0.0. I would like to update it to use SoftDevice 6.1.0 (as part of SDK 15.2.0) and perhaps...
Hi all,
I use nRF52832-QFAA, S132 2.0.0, SDK 11.0.0, IAR 7.5 under Windows
Upon connection, I am trying to resolve the peer "random private resolvable" address (not for...
we have designed a board using Nrf9160 IC and we have issue with SIM module. we not getting 1.8 volt in "SIM_1V8" pin. when running mqtt sample program we are getting
...
Hi,
Using nRF52840 with SDK15.0.0.
I started my projetc based on BLE tutorial characteristics.
I created my service and add 2 characteristics successfully.
My module...
Hi All,
Sanity check here. I'm reading the RSSI value from a received packet
if (nrf_esb_read_rx_payload(&rx_payload) == NRF_SUCCESS) { if (rx_payload.length > 0) {...
A device that is provisioned with PB-GATT enabled stops receiving mesh packets after the provision is complete.
When the provisioning process is complete nrf_mesh_disable...
HI,
I got the following log while advertising:
SOFTDEVICE ASSERTION FAILED AT 0x00014AA6
Since this address locates at softdevice, I can not know what happens.
Would...
Hello,
Using nRF52 DK boards, I'm trying the simple_message_model by modifying the light switch example.
With the client, I simple send a 12 bytes unreliable message by...
Hello! I have a question about nordic thingy 52. Is there any possibility to play more than 8kHz on this board? For example: if i will change speaker on another it could help...
Hello, How do I set the analog reference voltage to external pin P0.02? I'm using the arduino environment so I don't know how to set it via those registers? I'm currently...
Hi,
I am using SDK 15.0 on a custom board using nRF52840. Softdevice is 6.0.0. Coding with SES.
I am investigating and trying to fix the infamous IOS caching of characteristics...
In the schematic of the nRF52840-DK L1 and C4 form the matching network. C22 is noted with NP, but on the DK i have, is a component placed.
Since i would like to use the...
Hi to everyone!
I've been testing the Bluetooth on the nRF52832 DK board with some of the examples and I have saved the mac address (obtained from my smartphone).
In...
Hello All,
I was wondering if someone can confirm the consumption of the nRF52840 in SYSTEM ON when running the Power Management Example on the nRF52840 DK board (in nRF...
