I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Hi,
What should i do after i load mesh app in " github.com/.../nRF51-ble-bcast-mesh" adress?i have two board
When i download the app,why doesnt advertising exist.i cant...
hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hello,.
I have a question about using app_usbd_cdc_acm_read and app_usbd_cdc_acm_read_any in SDK15.2.0,
I am not sure I fully understand the description in reference...
nRF52832, SDK 14.0.0, SoftDevice 132 v5.
If SoftDevice is enabled but the system is not yet advertising or connected via BLE, will SoftDevice ever wake the CPU up from...
Although redirect.c is included and printf() calls use the uart as expected, fgets() calls don't seem to be able to detect incoming characters.
This isn't critical, since...
Checking QDEC (Quadrature decoder) of nRF52832.
But, In a SAMPLEPER Register(0x508) when set to 128us(0) or 256us(1) does not occur SAMPLERDY Event.
On the other hand...
Hi,
I am working on a project running on a nRF52832, using SDK 12.3 and S130. I use Eclipse (2018-12) as my IDE.
I have followed the explanations from this tutorial :...
Hi,
I am using a nRF52832 to communicate with a ICM-20948. I've been trying to write a 16 byte packet of data and read back and verify that same data. According to the ICM...
Hi,
I am trying to communicate from STM32 Nucleo board to murata's MBN52832, using SPI, with the nordic chip being the slave. So, for this I used the SPIS example from the...
Hi,
I am trying to get the ADC up and running on the nRF9160 DK. I had a look for example code and the latest I found was here.
https://github.com/Rallare/fw-nrfconnect...
Hi, I am using N52832 to developing a producation need to implements ANCS NC. I am using sdk 15.2. And I found the connection is terminated by the apple device after the reconnect...
I am using BLE peripheral UART application from nordic SDK version 15.2.0 SoftDevice S140 PCA10056 nRF52840 Development kit on Embedded Segger studio operating system - Windows...
I am trying to design some test cases to check the LTE stability and performance.
I avoid to use the existing Nordic samples to do this as they are too complicate for the...
I am migrating an existing project to nRF5_SDK_15.3.0, and I want to know why the error occurs and how to fix it ...
1. ..\_build\nrf52832_xxaa.axf: Error: L6218E: Undefined...
Hello to everyone.
I'm working with nRF52832 SDK (PCA 10040) and Segger Embedded Studio v4.12, in the Light_switch example for Mesh 3.10. Right now, I'm able to use the...
Hello to everyone.
I´m working with the Light_switch examples (server-client-provisioner) in BLE Mesh 3.10 for nRF52 DK PCA10040. I´m trying to make a network with 2 clients...
The links I found regarding this go to a "OOps" page. I need the original FW of the nRF51DK so that I can use it to flash my target board using nRF51822.
