I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
I am now based on nrf52832 SDK14.2 development, I tried to use the PWM driver and timer to drive the corresponding two IO port an irregular waveform, I originally thought...
I am using the Hackable kit which has nrf52832 to control a servo motor and read accelerometer(AXL335) readings through a iOS app. I am a novice when comes to embedded. I...
Hello, ererybody!
I use nRF52832,have a development board.
I was testing the adc module,using the ANI2 channel,I measured the ANI2 channel voltage to the ground,find it...
Hello everyone,
now i'm working with nRF52840 PDK( Engineering B ) and i migrate my project from SDK 14.1 to SDK 15. My starting point is ble_app_template and i want to...
Hi!
My setup:
* nRF52 DK (let's name it N )
* nRF5_SDK_15.0.0_a53641a
* s132_nrf52_6.0.0
* SES V3.34b 64-bit
* two android smartphones (let's name them A1 and...
1. nrf51822-qfaa
2. sdk10.0 & sd8.00
Q:
If the MAX_CONN_INTERVAL is set to greater than 200, NRF_ERROR_INVALID_PARAM will be returned when called sd_ble_gap_ppcp_set...
This post had a discussion on using one button but the first reply suggested a buttonless solution. So now I'm not sure if one button dfu is best if same button is used for...
hi,
i am doing a project where i have to exchange strings between nrf52832 as peripheral and andoird smartphone using nrf connect app, in this project data security is a...
Hello!
It's the first time using Nordic devices so i´m doing some SDK examples and trying to merge them. I'm using SEGGER Embedded Studio. Right now i´m using ble_app_blinky...
Hello,
I'm usign nRF52832 IC and SDK5. I want to awake the sleeping MCU by NFC and pair with BLE. In short Pairing device address should be transfer via NFC. There will...
Hi all
i am using SDK15, nrf52832 dev kit and s132 version 5
I followed the below steps:
1)Flash the softdevice
2)Update the generated dfu_public_key in secure_bootloader_dfu...
I am developing a firmware and connected a spi LCD to nRF52840, but I got the max speed only 8 MHZ, in Datasheet is 32 MHZ max.
Which speed of the SPI master is max ? (I...
I'm getting a disconnect reason of 0x3D / BLE_HCI_CONN_TERMINATED_DUE_TO_MIC_FAILURE during a connection attempt. It does not happen for all my phones except one. It appears...
Hello Everyone,
I am a beginner and working on nRF52832 DK using SDK v15 and using keil mdk armv5.25 as a compiler. Currently I am trying to modify an example in the SDK...
