I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Hi,
I noticed a bug in ble_ancs_c.c where it will write NULL-termination outside the attribute buffers added with ble_ancs_c_attr_add(). When the received ANCS notification...
I got a hardfault crash in the ANCS code, when an invalid ANCS notification was received from the phone: attr_id_parse() read 195 as attr_id, and used that as index in ancs_attr_list...
When one host and one device,the through can be 16KBps。But,when one host and two device ,the Max throughput is only 6KBps。Can you tell me Why ?????And Can you tell me the...
I use keil4. When the code size less than 15297bytes is ok. I will cause error when the code size bigger than 15297bytes.
Something must config in keil4?
Thanks~
I'm trying to listen to a bluetooth low energy connection between a smart bracelet and my smartphone. In Wireshark 1.10.1 I only can see the Advertising Indicators. As soon...
We are able to run both these services (experimental buttonless DFU and experimental app ble blinky) individually in Eclipse GCC, SDK 12. However, when both of the services...
I am intended to integrate the Nordic SoC nRF52832 in our PCB to generate a PWM.
However, I could not understand the difference between the following:
topicSchematic QFAA...
Hi to everyone, i have the mpu6050 code and i have to change it with parameters of adxl345.
i have this definitions:
#define ADDRESS_WHO_AM_I (0x75U) //!< WHO_AM_I register...
Hi, I am trying to connect a peripheral device which in this case is a BLE device called DELTA and I am trying to connect it to a central device which is the NRF52 board....
hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
In nRF5_SDK_12.1.0_0d23e2a in file: ...\components\softdevice\common\softdevice_handler\ant_stack_handler_types.h In lines 30-32 inside #ifdef ANT_STACK_SUPPORT_REQD is preprocessor...
Hi ,
I have nRF51822 beacon and J-Link LITE and i am using nRFgo studio setup .I am trying to flash the hex file in to the beacon using nRfgo studio.The beacon has two...
