Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
hi,
1.I find some same issues on website, most of them can send more than 1 packet per connection interval up to 6 packets, but I'm not sure what version of sofedevice...
Hi!
We are using S130 softdevice in peripheral role and achieve the specified maximum throughput of 63.4kbps ( S130 spec ) when communicating with a PC and connection interval...
Dear sir,
Reader has a NRF24L01P-R7 with stm32f4xx controller.We are using TAG chip NRF24LU1P-F32Q32-T.
Please share the independent stack information(source code) so...
I am trying to setup the examples for the dev board PCA10040. I copy them from the Pack Installer and when I open the project I keep getting "Install missing Software Packs...
Hello
I made a custom service with characteristic. It send the number 1234 over ble. When i open the Master Control Panel and look at the custom characteristic. I read...
We have a home made BLE device based on nrfR1822. This one has two embedded sensors sampling data at a frequency of 25Hz.
In regular mode, the device sends every second...
I was going through Gazell link layer as well as Enhanced shortburst i found in both of them we can use payload max upto 32 bytes. Both supports 8 nodes with an host using...
I just received the nRF52 demo board PCA10036 V 1.0.0, and I also downloaded the latest SDK nRF52_SDK_0.9.2_dbc28c9
I programmed the softdevice hex and then programmed...
Hi BLE Developers,
I'm developing a BLE peripheral device using S110 softdevice which doesn't have any input or output capabilities and will communicate with smartphone...
Hi,
I am using the iOS nRF Toolbox and integrate it to my Swift project.
After that, I got this error message.
Undefined symbols for architecture x86_64:
"_crc32"...
my dk board : nrf51422 and nrf 52382,
the central role : nrf51422, and the peripheral role is 52382.
my sdk version : 52422 is 10.0.0 and 0.9.2 for 52382
the project...
I've been trying to wrap my head around the app_twi library by looking at the examples, and I'm slowly getting there.
However, for my application I need to send multiple...
There is a fair amount of documentation suggesting that a Raspberry Pi or consumer router running OpenWrt can be set up as an edge router for Bluetooth.
The builds involve...
