HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
I have a question about Makefile template used in all samples in SDK12.x
What is the sense of:
$(foreach target, $(TARGETS), $(call define_target, $(target)))
-include...
nRF52832にてボタンレスDFUサンプルにEEPROMを実装させたいのですが、
必要なライブラリファイルnrf_cli.cやnrf_queue.cをプロジェクトに追加したところ、 nrf_cli.ｈやnrf_queue.hが「no such file or directory」となり、
ビルドが失敗します。
components...
I've been using the LPUART for comms between the 52840 and 9160 in a Thingy91; this was going well until I changed the nRF Connect version from 1.9.1 to 2.1.2, to resolve...
When I call nrf_pwr_mgmt_run() in my project to put the device into sleep mode, after a short period of time I get the error message:
ERROR 3735928559 [Unknown error code...
Hello all
I am having a problem with nRF Connect SDK where whenever I try to read from a sensor while bluetooth is enables, the software crashes. If I disable bluetooth...
According to the Kconfig documentation, https://nrfconnect.github.io/vscode-nrf-connect/kconfig/install.html , the active board is displayed on the Status Bar when editing...
Running a Thingy:91 now for 4 weeks from batter with one message exchange per hour, it stopped working (NB-IoT mode).
The client (Thingy:91) uses "sendto" and that function...
Was using SDK 1.9.1 up till now, but I migrated to SDK 2.0.0 and I changed my overlay file to add the pin control stuff. I have a nrf5340 and use the app_ns board config....
According the data written to NVM, is there a difference between "%XFSSYNC" and "+CFUN=0" ?
Reading the documentation, I see mainly user configuration be written.
I may...
Hello,
I am trying to add SDCard management, over SPI bus, into my project with nRF5340. When I try to compile, the error is always the same. I am trying the code over the...
Hello,
I have a problem that looks a bit like
devzone.nordicsemi.com/.../nrf52840-custom-board-won-t-boot-without-debugger-reset
For me, to be more precise:
nRF52840...
I just upgraded my environment from nRF Connect SDK v1.9.1 to v2.1.0. This process raised one critical bug, as well as some very important questions:
My projects make very...
The setup : nrf 52840 , NCS 1.9.1 , The SAADC is configured in advanced mode with 1 single end channel and double buffered with size of 16 (32bytes). RTC is configured to...
Hi,
I am reposting this as the previous question might have been closed due to inactivity from my side and the issue isn't resolved yet.
To follow up please check this...
