I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
Hi,
I am trying to add OTA DFU functionality to our project using 1-stage MCUBoot. It works fine when I use the default key, I can update OTA firmware. To add a custom key...
Hello,
I am using the Android DFU library . The constructor for the DfuServiceInitiator class accepts a device address. Can one assume that providing an application address...
Hi,
I use sdk153.IC is nrf52840.
Install NRF connect on Android phones such as Samsung vivo oppo. Only Samsung can quickly scan the broadcast and the connection is normal...
Hi Nordic,
I am using your QSPI example code and make it into functions for my application. The code could run if I block the rest part of my code and only run the QSPI...
Hi,
4 years ago we implemented a 802.15.4 and Bluetooth Multi protocol project on the nrf52840. Our application continuously ran 802.15.4 and bluetooth was just used for...
i tried to use the high voltage mode of nrf52840, but when i flash a firmware called "ble_app_hids_keyboard" which use the nrf52 sdk, all is good. but when i flash the firmware...
Hi,
I'm using nRF9160dk to configure MQTT . i'm new to MQTT so ,Is their any example code to understand and work on it by using " ZEPHYR RTOS "
thanks in advance.
A product I'm working on uses an nRF5340 (actually a Fanstel BT40 module with an nRF5340 in it) with NCS v1.7.1.
It's got an SPI slave connection (the nRF is the slave)...
good day,
is there a guide or tutorial on how to detect different press type in single button? will try to assign different tasks per button press types (single, double...
Hi Support team,
According our spec 52832 rx is about 5.4mA, but actually i measured our example, it is about 7.1mA, may i ask where is the gap? so i suspect it is because...
Hi,
I'm developing an application based on the nRF52832 development kit. It is nrf52dk_nrf52832(PCA10040). I have used nRF Connect SDK (3.0.0) for the project development...
Hello,
I am trying to interface the ble_hid_keyboard with uart using nrf52840-Dk in SDK 17.0.2. But not able to print data from uart and even not able to connect hid keyboard...
Hi,
I have an nRF9160 and working am off of the AWS_IOT sample code. When I start the device, the error messages occur 2-3 times and then the device connects successfully...
Hi,
I'm working on a custom board with a nrf9160 µC. This board is powered by a battery and a supercapacitor and my job is to assure the autonomy of the battery.
I...
I am using 9160 to develop a product for customers, which saves the date, time and other settings in NVS. Yesterday, I encountered a problem that the product could not start...
