I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
I have to implement a connection from my central device to another device with a specific name.
When I use the ble_app_blinky_c example everything works fine, BUT my central...
Hi, I have external PCB, looks like this:
Need help with flashing the nRF52832 chip via nRF52 DK, please. External PCB have identical pin assignments as QFN48 pin assignments...
So, i just got some modules from minew, those are MS50SFB2 ( https://www.minew.com/product/nrf52810-ms50sfb2/ ) based on nRF52810. I uploaded the blinky example on one of...
Hi,
I am using nRF SDK 1.9.1. Want to add a few ASSERT to check corner cases.
When I add the following code in main.c
__ASSERT(buf == NULL,"Test ","Test");
The module...
Hello,
I was trying to store some information in flash using littlefs. when I build and run the littlefs example alone it works fine as accepted. However, when I configure...
I have nRF52840 Dongle and I want to sniff packets between two BLE devices. When I search in the Nordic DevZone forum, there are inconsistent answer about BLE sniffing support...
Hello community!
I know this sounds almost impossible... but it's happening
I'm debugging an application based on peripheral_uart. When I call
bt_nus_send(NULL...
hello. I want to use the button as a pull-down. I am using nrf52832, and the button and circuit part are composed of pull-down and the code is written as follows.
However...
Hello,
I can't find anywhere the height dimension for the nRF52832 WLCSP. There is width, length but no height, what is the height of this product ? Thank you
I am trying to use puncover to estimate the maximum stack size for the created thread.
We also tried the thread analyzer, but gave up on it because it did not seem to be...
I am using S112 softdevice along with SDK 15.1.1. The chip that I am using is nRF52832 and ble uart example
I want to make advertisement non connectable and non scannable...
hello Nordic
i am working with nrf52832, ncs 1.7.1
i am trying to work with external flash driver (25lp128)
so my dts looks like this:
my configs are this:
myboard...
Hi,
For some time I'm developing application for both central and peripheral devices. The Idea is that both devices have a special mode in which they pair & bond and add...
