here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
We are experiencing an issue with the QSPI driver on nRF54L15 where external flash access stops working after a BLE bonding procedure.
The system works correctly until bonding...
Is there a sample project for the nrf54LM20A DK that uses the nrf_802154_radio_driver? We need to implement a custom protocol to work with existing products.
Thanks,
...
My VSC install is up to date, no updates pending in the Extensions manager etc.\
When building an app for nRF54L15DK I get a warning about the SDK being out of date, and...
I am using the nRF9151-DK as an SPI slave . The SPI communication is not working as expected, and the nRF9151-DK is not receiving any data from the SPI master .
I have configured...
Hello Nordic Support Team,
I am trying to upload firmware to my nRF54LM20B-DK using the nRF Device Manager application on my mobile phone .
For this test, I started with...
Hi!
I'm testing ubidots, which require a 35 character long username to connect with MQTT. This fails, and mqtt_connect gives me error -12 ENOMEM. The same code works fine...
HI,
As stated in the topic I have found several misalignments/issues in the following setup:
NRF Connect Desktop (v5.3.2) NRF Connect Desktop DTM (v3.1.4) NRF CONNECT...
nRF54L15: system clock stops permanently after a GRTC compare event is lost
Disclaimer
Claude Code (Opus 5) was used to assist with this investigation and with the drafting...
Hi, I just started evaluating the nRF93M1 DK (LABA version) and have questions about the firmware version.The AT+CGMR gives "mfw_nrf93m1_1.4.1", which seems to be a bit older...
We're based in India, developing a custom hardware board, and need to test CAT-M1 connectivity on-device. Since CAT-M1 coverage is limited in India, we're planning to travel...
I need an architectural guide and recommended workflow for setting up post-production (in-field) cryptographic key provisioning on Nordic nRF devices (nRF9160 and nRF9151...
Hi, we would like to create a kind of game using 2.4Ghz emitters . The 2.4Ghz USB Dongle emits and the mobile phone detects the frequency + embed unique ID/code so we confirm...
Hello,
we are currently developing a device based on the nRF5340 using LE Audio.
The device streams audio to a smartphone, where the corresponding Android application...
NRF52840
We are using NCS v3.3.0, however this issue occurs also on NCS 3.0.0.
When using the SoftDevice Controller stack. ie MPSL etc enabled, at times we enter SYSTEMOFF...
