I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
I have trouble developing BLE devices with Nordic NRF5280 and SDK 15.3.
I have a device that uses a custom BLE service, And when using nRF Connect on the mobile phone, all...
I have been developing some nrf52832 code (SDK 17.0.2) using the Segger RTT debug window for logging. I added the code from the UART example but the printf goes to the debug...
I'm planning to modify the nrf52832_ciaa reference designs in altium to emulate the functionality from a development kit and add an RTC.
I need access to pins P0.23, P0...
Hello. I would like to use an internal RTC to keep time going even if the power is off.
1. Is it possible to implement with 'nrf_calendar' module?
2. Should I think about...
I have a battery powered iOT device using BLE, I2C, and GPIO. I am focused on reducing the power consumption. When BLE is not connected, I want to have as little power usage...
This is in response to a central sending an update. I try and follow with the central's request except I set the times to the AUTO value. If I get an NRF_ERROR_NOT_SUPPORTED...
ran nordic blinky example on nrf52840 kit
Want to know where is the transmitter power set in the code.
refer any example where we can define transmit power
Hi Folks,
I am just asking general information (explanation and/or code samples examples) to set up a secured BLE connection between multiple centrals towards one peripheral...
Hi,
I'm programming a nRF52832 for SPI communication with another device which requires some single byte TX/RX. After a lot of head-banging, I realized that the nRF52 was...
Hello there,
if i download a hex-file to the NRF52840-Dongle with the J-Link (Lite) tool, the dongle always remains in bootloader mode (red led is flashing). But if i download...
Hi,
I recently updated to version 1.5.1 of the SDK, which includes a new version of emStudio. All seems generally OK, and so far all of the real issues I've found have been...
Hi Want to implement dimmable LED light Bulb with nrf mesh SDK (one pwm and on-off ) Which example from NRF SDK i should refer for this functioality. Thanks and Regards, ...
Hello,
We are trying to develop and test our coded phy BLE interface. We have used the iOS and NRF connect app to test the 1M services and characteristics, is there an equivalent...
Hey, I've learnt that nRF5 SDK is having the capability to implement the AoD (transmit) and AoA (receive) to precisely calculate the location indoors. Kindly help me to get...
