Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
Hello,
The Bluetooth SIG has just released the LC3 Codec specifications on they website.
So my questions are:
- Can we use the nrf 52840 with this new codec for our...
I Flashed the DK using segger embedded studio with example "pca10056_s140_ble_debug" After that I am unable to flash "ble_app_uart" example.
I tried another example like...
Hello,
I am trying to do a long term connection test to the nrfcloud. I have updated the nordic sdk to v1.2.0 and am running the asset tracker on the dk board. I have set...
Hello,
I'm using nRF52840 chip with nRF5 SDK 15.2.0 ,Mesh SDK 3.1.0 and soft device S140 6.1.1
I'm trying to protect the flash if a shutdown occurs during a write. Reading...
From what I understand, the nRF52832 supports the following BLE5 features:
-2 Mbps
-CSA#2
-Advertising extensions
The chip does not support the 'Long Range' feature...
Which of the configurations will work and how?
1) Single Nordic device acting as a Nordic_UART peripheral and multiple smartphones with UART application (central) receiving...
Hello,
nRFSD5 v16.0, softdevice v.7.0.1, nRF52840
We have an application where we receive data from mobile application whenever it writes to a certain UUID. The data is...
Hi...
How to read and write to the external flash
I am using sdk 15.2 version, interfacing the development kit nRF52832 with w25q64 external flash via spi. I have read...
Hi,
I have a Thingy:91 v 1.0.0 which runs fine with the provided asset tracker firmware thingy91_nbiot_dfu_2020-04-29_bc7ade8b.hex. Cloud connect also is fine.
I managed...
Hi Didrik Rokhaug,
sdk:ncs v1.2
Routine path:D:\ncs\v1.2.0\nrf\samples\nrf9160\at_client
The routine is attached:
The test results are shown in the figure below: ...
Hi,
I want to update the firmware of my Nordic controller nrf52810( DFU Target ) using ESP-WROOM32(DFU Controller) using BLE protocol.
Please suggest how to proceed. ...
I am trying to communicate between my mobile Bluetooth and a BLE sysyem (Bluetooth low energy chip and evaluation board). The BLE chip I am using is NINA-B301 and evaulation...
I experimented with nRF52840 for 1 month. It was uploaded to the board well before, but suddenly I can't get the port.
So after finding a lot of Q&A, 1. Press button-4 ...
I've just moved over to the latest SDK version 1.3.1 (i uninstalled the previous version before installing the new one)
I installed it via the toolchain manager as usual...
Running an application that is using a 32 Mhz SPIM3 interface and it is working fine on our custom board.
As part of the interface testing, a logic analyzer was used to...