hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
We have the following setup:
- nRF52832 XXAA
- SDK 6.0
- S132
I have attempted to add a memory guard into the location preceding the application RAM data block start...
Despite following the procedure listed below, no text appears on the OLED display, despite the driver being able to communicate with the device.
I am using nRF Connect SDK...
I am looking to get some clarification on the QFN94 footprint of the nRF5340. There are four corner pads and they do not appear in the mechanical specifiications section 9...
Hi,
When looking at the reference schematics and reference layout of nRF5340 I notice that pins A25, B12, B26, G1, H2 and J31 are grounded:
Figure 1. Circuit configuration...
Hi, with my nrf9160 I need to send a gps location every 3 sec to azure, so I combined the agps and the azure iot hub sample. It's working pretty good but 10 sec as a periodic...
Hi, I doing PCBA prototype. And I found part number nRF5340-QKAA-R and NRF5340-QKAA-AB0-R7 in the website. In my understanding. The NRF5340-QKAA-AB is a sample engineering...
Hi,
I want to used NRF5340-DK for my BLE receiver evaluation I find LNA (NRF21540-DB) which is suitable to use with NRF5340-DK.
But I could not find this available in...
I am just beginning with the dev kit I bought in December. The box has a URL: nordicsemi.com/start52840dk
This is not helpful. The only thing I find there is a PDF - apparently...
hello,
i am using sdk 17 with ses v5.20 i have customised board consists of Decawave 1000 , Nrf52832 and accelarometer i want to compile and run both initiator and responder...
Please tell me about RBP CONF of UICR. Q1. What is the purpose of UICR's RBPCONF (read-back protection)? What kind of protection is it? Q2. What changes when RBPCONF (read...
I'm having problem connecting my thing:91 to the nrfcloud. When im trying to connect im getting "Troubleshoot nRF Code 40412". One of the reasons could be "before attempting...
Is there any way to run the TIMER peripherals off of the 32khz clock? We need to generate a 1khz PWM while the micro is asleep, and we really need to be able to shut down...
My device has BLE and I can successfully use any example (for example ble_peripheral/ble_app_bps ) to advertise different services.
It also has a serial port from where...
