hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hello Everyone,
I'm looking for an MCU that could be used as a master for SPI communication to supply the necessary signals (CS+, SCLK+, MOSI+) to a slave device (amplifier...
Hello,
I have migrated my codebase from v1.3.0 to v1.4.0 of the nRF SDK and have a strange issue now where the serial port is spitting out sleep debugging information in...
Hi,
The nrf52832 product spec shows all the clocks provided by HFCLK and LFCLK. But where can I find which peripheral is using which peripheral clock specifically?
For...
Hi,
I need to read some BLE characteristics presented by a commercial device nRF52-based, using my nRF52-DK, based on the nRF52832 and PCA10040. I don't have the firmware...
Hello experts,
I would like to get my mind clear on this.
I am using NRF52833 for our custom board we are using Zephyr RTOS (NCS v1.4.99) and IDE is segger embedded...
We need to accurately control the time when the Bluetooth advertising package is sent out, so that the two slavers can simultaneously send the beacon data to produce the signal...
Hi,
I am facing an issue when setting up advertising intervals (in connectable mode).
Whatever the value I enter I will always end up with an advertising interval of...
Hi,
I am currently working on the ble mesh project. I would like to know whether there is any cybersecurity related examples in SDK .
1. Can you list out some of the security...
Hi,
So there is a dataflash MX25R6435F available on nRF9160 DK.
My question is that is it available for general purpose? If yes then how can it be accessed?
Unfortunately...
I am trying to use the PCA10059 dongle as the connectivity device with pc-ble-driver-py
The script I am using works with a PCA10056 devkit loaded with the connectivity firmware...
I now integrate USB, BLE, LLPM, keyboard HID and Mouse HID to nrf52833.
When I added CONFIG_DESKTOP_HID_MOUSE=y, my project was abnormal.
BLE connection: Move Mouse and...
Hi all, I have a little problem regarding "background scanning" example.
Setup: - SDK 17.0.2, softdevice s212, Segger - Master ANT+ = Nordic DK PCA1040 with ANT+ Tx profiles...
Hi,
I'm using nrf52840 device in order to connect a mobile via BLE.
After pairing and a couple of minutes - I get a discinnection with reason code BLE_HCI_LOCAL_HOST_TERMINATED_CONNECTION...
I'm trying to open a nRF Connect SDK project in Segger Embedded Studio for ARM (Nordic Edition) V5.30a
I have followed the instructions on the following page: https://developer...
Hello everyone, I hope you are good.
I am starting out with the nRF52811 and I'm completely new to the SoC world. I have a few questions regarding what I would realistically...
