HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
I have a question about Makefile template used in all samples in SDK12.x
What is the sense of:
$(foreach target, $(TARGETS), $(call define_target, $(target)))
-include...
I need to run gc because I get rc =FDS_ERR_NO_SPACE_IN_FLASH.
So I run gc simple as written in https://infocenter.nordicsemi.com/topic/com.nordic.infocenter.sdk5.v15.3.0...
Hi all
we used a nrf52832 to communicate over SPI and I2C at the same time with some sensors. This works fine.
At the moment I try to convert the project to nrf52810 but...
Hello,
does anybody now when the sniffer will support coded PHY?
I found a similar questions but no answer yet...
https://devzone.nordicsemi.com/f/nordic-q-a/42216/does...
Hi,
I would like to combine NFC - BLE pairing and launch app record. Naively I thought I would write the second data right after the first:
But this does not work. Reader...
I am using an NRF52832 on an energy harvesting board where lowest power is critical. I can achieve ~2 uA current consumption in idle state (waiting on RTC interrupt), wake...
Hi,
I work on the nRF52840 DK with the ble_app_uart example and I want to add a timer using app_timer api,
in order to create RTC time/date timestamps for my sensors raw...
Hello
I am using SDK15.3 and nrf52832 development board.
In my setup,
1. I have a few peripheral nodes whose only job is to transmit some arbitrary packets ( say P)...
My setup consists of a Raspberry pi and a PCA10056 dev-board (NRF52840). I followed the instruction from here in order to set up the Raspberry pi as boarder router and connect...
Hi all,
I am working on the Smart remote and when "spamming" a lot of key simultaneously, I sometimes get a warning "m_coms : packet lost" and then a disconnection.
...
Hello,
I have a Taiyo Yuden EYSHSNZWZ module. I also had a breakout board manufactured for it to get access to all the pins. I am having trouble trying to program the...
Hello,
I`m trying to get this ( https://github.com/NordicPlayground/nrf52-ble-multi-link-multi-role/ ) working properly to test the possible working range between two nRF52840...
To the kind attention of the Nordic support team,
Hi to you all, I have got legacy gazell code running on nRF24. In old code the following instructions was used:
hal_nrf_set_address...
My customer wants to do a range test with a propritary 802.15.4 software.
Do you have an example for the nRF52840DK with an blinking led if the communication is established...
Hello,
i want to display a string in 5x21 led matrix using HT1632 Led driver
Using SPIM0 Protocol i should send data from nrf52832 to HT1632 led driver
My question is...
