hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi i am using SDK15.2, nrf52832 board.
Which function is necessary to achieve multilink in example code. I dont understand how the central is connecting multiple peripherals...
I just purchased this unit and followed the setup instructions. I did not perform any flashing. When I plug the usb into the computer the jlink drive doesn't show up in Windows...
Hello, I am not sure if this was noted before. I didn't find anything about it. This is more of a suggestion. I was looking to use Thread CLI Example to use with the pca10059...
Hi,
I am using a custom board with the nrf52810 and trying to interface with the SHTW2 sensor. The sensor has an I2C interface and hence I use the TWI peripheral for this...
Hello,
I have a question regarding BLE_GAP_EVT_CONN_PARAM_UPDATE (nrf52840, SDK 15.2).
I'm evaluating the BLE_UART example using multiple peripherals. The goal is to scan...
I have an nrf52840 that the fds_init function is returning an error 11 (NRF_ERRO_INVALID_DATA).
What would be the most likely cause of this?
The code is based on the THREAD...
Hi,
According to the NRF52840 product specification document the default value for REGOUT0 is 0xFFFFFFFF.
When powering the VDDH this implies that the VDD power is 1.8V...
Hello,
I am using nRF52840 Dongle and I want to use AIN0 pin for reading a sensor data. I was using PIC for this kind of project(C Programming) before nRF52840. Here my...
Hi I am trying to do the dtm testing, however when I clicked on the link to download the zip file it says page not found, I am wondering where can I download it? Thanks!
Dear nordic,
I have some doubts in this example based on thread. Thread says one node join to the network using by commissioning.
1. In this example where we start commissioning...
I'm sending data from my phone to the device using nRF Connect app for android as follows
uint8_t SoporteBLE::enviaTiempoEspera() { uint8_t tiempoEspera; if(Bluefruit.connected...
Hi
In the Mesh model specification, The Generic Power OnOff Server model extends the Generic OnOff Server mode.
According to Mesh Profile 4.2.3 Subscription List, Power...
nrf51822 production is sometimes hanging (no response) in high current state (almost 250 uA -> normally 20uA).
before this issue, there is similar issue about twi that waiting...
Hi ,I'm working on nrf_MESH v2.20 and nrf_SDK v15.0 and SESV3.40.
In the project of light_switch->proxy_client ,I use printf() to print something and it can work well and...
