I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Hello,
I am using sdk 12.2.2 and nrf52 customised board. Now my challenge is as follows.
When I am adding this in my code.
nrf_gpio_cfg_output(26); nrf_gpio_pin_write...
Hi all,
I use nRF52832 with the UART peripheral example.
I try to enable connection event extension in the device and get an error.
I use SDK V15.0.0 and Softdevice...
I've been trying to find a way to program a hex file onto the dongle via the command line on linux.
I would very much prefer not having to touch the mouse in order to program...
Hi, I was hoping someone could tell me if/when a version of the nRF Mesh Android App found here:
https://www.nordicsemi.com/eng/Products/Nordic-mobile-Apps/nRF-Mesh
Will...
Hi,
I'm using NRF52840 sdk v15 with Softdevice.
I have multiple SPIM instances and I make sure they are never active at the same time.
Can I share the pins (except the...
Hi, I'm trying to rate nrf52832 with stack ble_app_uart softdevice. My IDE is the IAR workbench for ARM 7.80.4. I downloaded the latest version nRF 5_SDK_15.0.0_a53641a, which...
Hi:
I would really, really, love it if you could provide a Segger SDK for Thingy! I've seen a few threads in here about the work to do it and it's a struggle. I noticed...
Hi there,
I've been searching around this forum for a while and still haven't gotten any reliable answer. I'm trying to develop a OTA firmware upgrade solution for the ATMega328p...
Hi:
when I compile project Thingy_ndoe in solution Thingy_node_s132_pca20020, an error meet,
C:\Nordic\thingy_sdk_v2.1.0\mesh_sdk\mesh\access\src\nrf_mesh_node_config...
I have combined the light switch server and client model to build control model. When i start provisioning for control model opcode status field : 2 error occurs which means...
Hi ,
I search nrf52810_bitfields.h , but i don't find about start bit , is the direction search for error ?
My idea : This is set up for stop bit , should the start bit...
Hi All,
I have serious difficulties to work with this board. I'm a beginners and I did not find any tutorial where I could said...oooh great I understood. My goal is to...
Hello all, I am trying to write a program that that updates the firmware on an external chip from a smartphone over BLE. Currently my approach is working but quite slow and...
Hello,
I am using a nrf52840 DK and I have no issues connecting to nrf connect. However, when it's connected all LEDs turn off and whatever code that was inside stops functioning...
Hi
I am programming NRF-51 board using nrfgo studio, it was working fine previously but now it failed to detect the board showing error. I shared screenshot of nrfgo studio...
