I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
Hi
Just to be sure: I've recently bought the nRF52840 Preview DK (dev board for nRF52840) but I think I'm going to use the nRF52832 instead for my project.
Is it ok to...
Hi i want to create a new project in Eclipse. I did this my following the complete code form git hub for devzone.nordicsemi.com/.../
*Nordic has provided sample code for...
Hi!
I've based a new project for the nRF52840/S140/Preview-DK on ble_central/ble_app_uart_c .
I use the NRF_LOG_XXXX macros for debug and they print fine in RTT Viewer...
Hi,
I have two nrf51822 device, on work as GAP Central, another work as GAP Peripheral.The two device use different connection parameters, after the connection is established...
hello,
i have developed one board using nRF52832-QFAA and trying to dump simple LED blinking code in it using nRF52 DK board. But code is always dumping into custom board...
How do you do
Now need pwm_driver demo5 duty ratio, is there any way to 1/6 or 1/8?PWM and phase difference is 4 road？
Ask for a few days, change seq_values [], but how...
I am developing firmware using S132 (SDK 11) for a custom board.
After performing Pstorage Update, if I do not wait for the callback from pstorage before continuing execution...
I am currently working with a the nRF5x bluetooth chip family and connecting to a windows 10 device as a central. I am using uart to get some visibility into what is happening...
Greetings -
I recently downloaded the latest SD140 images, 6.0.0-6-alpha, and began having issues with BLE communication.
I'm developing a custom device, based on the...
Hi to everyone!
I have a problem with the NRF_LOG or with RTT Viewer.
I wrote this simple code, just to test an output console.
int i = 0;
while (i< 100)
{
NRF_LOG_INFO...
When a Jlink programmer is connected to multiple devices (daisy chained) how do I specify which device is being programmed on the command line using nrfjprog?
Additionally...
Hi
I am making a speed cadence sensor.
I am using the gpio event handler to check the cumulative wheel revolutions and send the recorded value to the app as a time handler...
Hi,
Once the main hardware init part is done, system idles for a while and then I get a hardfault (APP_ERROR_CHECK returns fatal)
I reset the chip, and asked it to continue...
Hi,
Currently i am trying to understand the gazell api using the nRF5 SDK v14.1.0 example gzp_dynamic_pairing. Within my process to trying to understand the gazell api...
I am planning to design BLE MESH based LED lighting system.
(control involved LED ON/OFF , varying two PWMs to control intensity for warm & cold LED drivers, etc)
For...
