I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
Hi all,
I am testing this example and I have some question is possible using theR same NFC to turn off the nRF52? I cant see where the NFC event is handle
Can some one...
Hello,
Has anyone been able to succesfully use the HID Keyboard Demo (ble_sdk_app_hids_keyboard_main from Nordic nRF51822 SDK ver 6_1_0 along with GCC compiler for s110...
I have an application working using PPI to start a SPI master transaction from a GPIOTE event. Unfortunately, I currently have very high current consumption which I am led...
hi all,
i try to use to timer to have a single press and a long press.
this my code.
const nrf_drv_timer_t TIMER_BUTTON = NRF_DRV_TIMER_INSTANCE(0);
const nrf_drv_timer_t...
I don't know where it is used..
example, when I use sd_ble_gatts_hvx(conn_handle, &p_hvx_params), conn_handle was BLE_GATT_HANDLE_INVALID(0x0000) result of debugging. ...
I use nRF5_SDK_12.2.0_f012efa to develop BLE application in IAR workbench. Now I want to test the example: ble_app_template_pca10040_s132-nrf52832_xxaa. The project can pass...
First off, I have worked through Vidar's excellent tutorial located at " devzone.nordicsemi.com/.../" and have successfully built and run the blank blinky example so my installation...
Hello,
I am trying to change the MAC address of my device nRF52, by using NRF_FICR->DEVICEADDR[0], NRF_FICR->DEVICEADDR[1], I am able to see the device address.
But...
Hi I am using SDK 12.0.0.0 in nRF52832 in this code when I am using __enable_irq(); function for enable the interrupt then controller is getting reset can anyone help me regarding...
Hi,
I was trying to plot incoming ADC variables using Keil Logic Analyzer function inside the IDE.
So far no success; I am able to use it when using STM32 board.
...
I am getting confused when using nrf_gpio_cfg_input(PIN_12,NRF_GPIO_PIN_PULLDOWN)
should i keep it as NRF_GPIO_PIN_PULLDOWN,PULLUP or should i use NRF_GPIO_PIN_SENSE_HIGH...
Hi!
Using the out of the box ANT shared channel demo with a NRF52-DK board and the iOS demo app everything compiles and installs nicely, using the Android-based app nRF...
I'm working on a proximity beacon application using the nRF51 DK and a Nordic Beacon. The application basically has the nRF51 DK connect to the Beacon and monitor the RSSI...
Hi All,
Just want to ask if there is a better or recommended way to manage priority interrupt.
My application uses 3 interfaces:
SPI as master to interact with...
Hello,
I have an BLE application were I want, for security reasons, to allow a connection only if a button is pushed or if the devices already have bonded before. The Button...
