I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Hi,
What should i do after i load mesh app in " github.com/.../nRF51-ble-bcast-mesh" adress?i have two board
When i download the app,why doesnt advertising exist.i cant...
hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi,
I have a JLink script which sets APPROTECT in the UICR to enable readback protection and disable the debug interface.
For development purposes, I would like to be...
Hi,
I tried to use nrf51822 to update light intensity of 64 area to smartphone and then the smart phone will display those light intensity values in gray scale. I want...
Hi everyone!
During the development of our device, we faced with some problems:
So now we need to read the data array in a clear sequence from characteristics. The data...
Hi,
I have a device running firmware from SDK10 and using s110. I would like to update the device to use SDK11 firmware with S130v2. I'm using following code to generate...
Hello,
my application hex used to work fine before i change my bootloader and softdevice
now after falshing all the hex including the application , it is advertising as...
Hi,
I want data read from my sensor (gives continuous data when button is being pressed). and then send it through Bluetooth equipment.(PC or iPhone and so on) But i don...
nRF51_SDK_9.0.0_2e23562
S310
/*
* Setup the gpiote to handle pin events on the MMA8451Q INT1 pin. For the
* accelerometer we want to detect high->low transitions in...
hello everybody,
I'm working in a project & have to do something like security for the connection & be able to do updates to firmwares, someone suggested that doing bonding...
In past , I was able to perform DFU-OTA over BLE transport for a custom board that has nRF51822QFAA (256kB main flash memory) SOC. I tested this functionality with Nordic...
I am trying to setup a nRF51422 Development Kit (PCA10028) v1.1.0 board with ble-sniffer_win_1.0.1 sniffer. I programmed the Dev board with firmware version ble-sniffer_nRF51822_1...
Hi all,
I am using ble_app_uart application to send data to a Bluetooth device. I am sending the data to the Tx Rx Pins of nrF51822 module via an external controller. My...
Hello forum, I've been trying to get SOME alert on my nRF51DK from a phone. I first tried the alert_notification example, but it appears that one has to write a custom Android...
I'm trying to build the blinky example in SDK 11 and load it onto a PCA10000. I'm using the make file in PCA10031/blank/armgcc and am building this under linux. If I use blinky_blank_pca10031...
Hello All,
I am using nRF51822 with SDKv10.0.0 and s110 soft device with RTX os. My project have 5 different threads with 1000 bytes of memory is needed in each thread...
Hello,
I have a project where I wish to have BLE operation while active and use RTC1 as a calendar keeper while in low power mode. So far as I have seen, the softdevice...
