HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
I have a question about Makefile template used in all samples in SDK12.x
What is the sense of:
$(foreach target, $(TARGETS), $(call define_target, $(target)))
-include...
Hi everyone,
I am new to nRf series and have just started to use the nRF51 Development kit(nRF51422). I am using the s130 softdevice and I have seen that the sofdevice supports...
I'm trying to test out pin change interrupts using the PCA10028 dev board. I'm using two buttons to turn off and on an LED. The code below is only generating events from button1...
I have a custom board designed which implements a Arduino Micro (ATmega32U4) and an nRF8001 chip based upon Richard Clarks' nRF8001 breakout . The Arduino FW uses a slightly...
Hi.
Is it possible to enable the encryption of data which corresponds to the particular characteristics? i tried with BLE_GAP_CONN_SEC_MODE_SET_ENC_NO_MITM, for setting the...
Hi,
how is the new nrf_drv_twi supposed to be used for reading registers?
The sequence for that is pretty much industry standard:
> Device address
< Ack
> 0x00 (register...
I'm running the ble_hrs example provided on my nRF52 board. The thing is, I'm unable search my device using both nRF Master Control Panel and normal Bluetooth connection from...
I am using a central S130 softdevice in an nRF51822. I connect to a peripheral using sd_ble_gap_connect(&m_peripheral_address, &m_scan_param, &m_connection_param) . If it...
I am trying to provide a custom peripheral service with a 128-bit UUID in an nRF51822. I would like to use two bytes of the UUID to encode a piece of information unique to...
Hello,
am I right to assume that if sd_ble_gattc_write returns anything other than SUCCESS, then the packet was not queued?
Is this also true for BLE_GATTC_EVT_WRITE_RSP...
Hey guys,
I have a little problem on a new board comunicating with a MPU9250 sensor.
Chip version is nrf52832-QFAA-BA
GPIO PINS Used P0.20 (SDA) and P0.21 (SCL)...
The S332 v0.6 has been released and it is supposed to be compatible with SDK11. My concern is that in the release notes of SDK 11, it says "Temporarily removed support for...
I tried the above example but it hangs here:
while (ser_sd_transport_is_busy());
Not sure why, I'm using GDB to step thru code, and it appears always busy...
Is there...
Device: NRF51-DK
I'm using GDB+OpenOCD to step thru code and it appears that the nrf51 resets itself after calling:
SVCALL(SD_BLE_GAP_ADV_START, uint32_t, sd_ble_gap_adv_start...