We are having a slight issue when we are trying to update the DFU. The original version had this setting for the data reserve:
#ifndef DFU_APP_DATA_RESERVED
#define DFU_APP_DATA_RESERVED...
Hello!
I am working with the example mpu interface projects located at the following repo:
github.com/.../nrf5-mpu-examples
After converting the Keil projects to...
I'm using S332 0.9.1 with freertos. nRF52.
BLE and ANT are both active. I would like to run the ANT continuos wave (CW) test after a specific trigger (a command over a console...
I want to encrypt advertisements using aes-ccm peripheral present on the nrf51 board. I am not using softdevice, instead I am generating my own packets and transmitting them...
Currently, it using the I2S at nRF52832.
I want to play the wave file,But can not play well.
So, I ask you for a check because there is the following question.
[Question...
We love the radio range of the Nordic bluetooth chips. I am looking to see if anyone is developing a long-range bluetooth pendant or wearable? if so, I interested in perhaps...
I'm trying to read 8 adc channels using SPI, but then if I dont put some nrf_delay_ms the MISO return nothing and the CS is being driven low by default, high or a period of...
Hello Nordic team!
We are using nrf52832 chip and soft device S332. System runs custom bootloader and main application.
We did not have any major problems with BLE...
Dear Nordic Team,
The founders Lukas Pilat and Robert Kopka have met your representatives at the Light & Building conference yesterday. They recommended us to get in touch...
It seems like VS Code debugging will reset debugger if you click to reset MCU. This somehow leads to it dropping RTT. It further releases the CPU while reconnecting and halts...
Hello Nordic Experts,
Recently, I am using the nRF52840 dongle to sniff the Scannable Directed event, but I found that the AUX_SCAN_REQ cannot be sniffed, but the SCAN_REQ...
I'm using the UDP sample from SDK 1.8.0 with the following modifications:
No PSM
No eDRX
Send 100 bytes every 15 seconds
This is on the nrf9160-DK board.
I suspect...
I'm using embedded rust for a project on the 9160. If i configure any of the AIN0-AIN7 pins with the SAADC, my sleep current is 850 uA. Default config is resistor bypass,...
Hi,
I want to use NRF_RADIO->SHORTS register in my standard BLE application.
I am using nRF5 SDK15.
When I write in to this register before enabling the Softdevic, it...
hi,We developed a Bluetooth product based on NRF52832, but the bandwidth test was not qualified. According to the requirements of FCC Part 15.247 regulations, the Bluetooth...
Hello,
I have a project that is based on the peripheral_uart example that receives start and stop commands from a periperal_central device via BLE to send ADC samples...
Based on the NRF52840DK, we want to do a USB CDC DFU upgrade function, but we don't want to use the BLE demo. You want to enter the duf mode by adding and modifying registers...
I am facing a problem. Two sensors are triggering with data_ready pins and a timer value is captured upon the event. But the value can be stored only in RAM if a context switch...
HI,
I am working on nrf52833 board, while working with flash in dts file i could see that write_block_size is 4 bytes. Is there any way to reduce that , i need it as 1 byte...
Hello guys.
I am using a board based on the NRF52840 device. We run a code that we developed earlier and it was not well coded but working. it involves the interfacing of...
I am using Nordic Uart Service (NUS) to transmit raw data from nRF52832 device to iPhone. But it takes longer time than I except. Can I add debug message to make sure CRC...
