void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
Hi,
NCS v3.4.0, based on bluetooth mesh light_ctrl sample
nRF54L15-DK
I want to use P1.06, P1.07 and P1.14 as GPIO to toggle waveform, so I modify light_ctrl sample...
I am trying to get a Holyiot 21017 dongle to work correctly as a Thread RCP. The Holyiot 21017 has a nRF52840 and a RFX2401c power amplifier. In VS Code with the nRF Connect...
I am working on a BLE project on the nRF54L15, and I need to add the FOTA over BLE bootloader to it for cpuapp_ns.
I am using NCS v3.4.0 which no longer uses the Sysbuild...
Hi everyone,
We are a research group at a university, working on indoor positioning systems based on Bluetooth Low Energy (BLE) technology. We are currently evaluating different...
For just a first test board off of Thingy 91x design, can nRF5340-CMAA be replaced with nRF5340-CLAA? What's the downside of doing that? Documentation says it's not recommended...
Hi,
I have a question regarding the transmission duration in the Online Power Profiler for BLE (OPP). More precisely, it is about the transmission duration during a connection...
We are experiencing an issue with the QSPI driver on nRF54L15 where external flash access stops working after a BLE bonding procedure.
The system works correctly until bonding...
Is there a sample project for the nrf54LM20A DK that uses the nrf_802154_radio_driver? We need to implement a custom protocol to work with existing products.
Thanks,
...
My VSC install is up to date, no updates pending in the Extensions manager etc.\
When building an app for nRF54L15DK I get a warning about the SDK being out of date, and...
I am using the nRF9151-DK as an SPI slave . The SPI communication is not working as expected, and the nRF9151-DK is not receiving any data from the SPI master .
I have configured...
Hello Nordic Support Team,
I am trying to upload firmware to my nRF54LM20B-DK using the nRF Device Manager application on my mobile phone .
For this test, I started with...
Hi!
I'm testing ubidots, which require a 35 character long username to connect with MQTT. This fails, and mqtt_connect gives me error -12 ENOMEM. The same code works fine...
HI,
As stated in the topic I have found several misalignments/issues in the following setup:
NRF Connect Desktop (v5.3.2) NRF Connect Desktop DTM (v3.1.4) NRF CONNECT...
nRF54L15: system clock stops permanently after a GRTC compare event is lost
Disclaimer
Claude Code (Opus 5) was used to assist with this investigation and with the drafting...
Hi, I just started evaluating the nRF93M1 DK (LABA version) and have questions about the firmware version.The AT+CGMR gives "mfw_nrf93m1_1.4.1", which seems to be a bit older...
