Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
I have a question about Makefile template used in all samples in SDK12.x
What is the sense of:
$(foreach target, $(TARGETS), $(call define_target, $(target)))
-include...
Has anyone used a graphics library like emWin or TouchGfx on nRF52?
www.segger.com/emwin.html
http://touchgfx.com/en/
I do not see any posts on either forums or here...
Hello Nordic Experts,
I almost finished the development for my mesh project with nRF52840. But I faced some t ricky issues when in mass production. that is the time for...
Hi,
I am using SDK15.3.0 and s132_nrf52_6.1.1_softdevice. (nRF52832)
Getting higher current consumption ( 300uA ) while using the PWM library. ( https://infocenter.nordicsemi...
Hello, everybody.
I bought the nrf5340-dk board and tested the zephyr sample code. The Blinky code is worked. I tried the beacon sample code. But it is not worked. I think...
Hello ,
I have interfaced one NTC sensor with above attached image and below information :
SAADC pin : AIN2 ( NTC - pin )
VCC_nRF voltage = 3.3V
R14 = 51KOhm , 0.5...
Hi Team,
We have some application for using the oversampling code but we are facing some issue in that, we try to use the oversampling example to ours code but its calling...
Dear sir,
When use the template project(Which is in peripheral) for UART tx & rx is not working in without debug, but if i use base project(Like uart) file it is working...
Hello, I've seen some similar questions about resets after downloading firmware, but haven't been able to find the solution to my problem.
I'm using a Minew MS88SF3 NRF52840...
Hi,
We have a working application that allows FOTA when using the SDK 15.2 bootloader. We have recently tried to migrate this to SDK 17.0, and everything works except for...
Hi
I needed assistance to get the SKY66112-11 FEM working with the Radio Test Example, for certification testing (FCC, CE etc). I am using the NCS 1.5.1 SDK. I am using...
Hello,
I am using example code of MAX30101 Pulse Oximeter sensor with nRF SDK v1.5.0 on board NRF5240DK. I copied the example from the ncs \ v1.5.0 \ zephyr \ samples \...
Hi,
I am doing Mesh DFU , but there only have mesh bootloader hex file , I need to change bootloader source code, does there have some example? or where can I get the source...
Dears,
I didn't find any size information about IN105 & AN118. Would you kindly please help to provide a complete reel size drawing? Many thanks!
Best Regards!
Ricky...
I started working with BLE and I have some trouble understanding few things. The connection interval happens every X ms, that is set by master, usually the default is lowest...
Hi,
I want to combine ble_app_blinky and uart_pca10056 examples to get the uart communication(between terminal emulator and application) in ble_app_blinky app. I followed...
In the piece of code, where Ble_Stack_inti has been defined, err_code = nrf_sdh_enable_request(); DISPLAY_ERROR_IF_ANY(nrf_sdh_enable_request) APP_ERROR_CHECK(err_code); is...
