Hello!
I am working with the example mpu interface projects located at the following repo:
github.com/.../nrf5-mpu-examples
After converting the Keil projects to...
I'm using S332 0.9.1 with freertos. nRF52.
BLE and ANT are both active. I would like to run the ANT continuos wave (CW) test after a specific trigger (a command over a console...
I want to encrypt advertisements using aes-ccm peripheral present on the nrf51 board. I am not using softdevice, instead I am generating my own packets and transmitting them...
Currently, it using the I2S at nRF52832.
I want to play the wave file,But can not play well.
So, I ask you for a check because there is the following question.
[Question...
We love the radio range of the Nordic bluetooth chips. I am looking to see if anyone is developing a long-range bluetooth pendant or wearable? if so, I interested in perhaps...
I'm trying to read 8 adc channels using SPI, but then if I dont put some nrf_delay_ms the MISO return nothing and the CS is being driven low by default, high or a period of...
Does rbc_mesh_value_enable() API is designed for ? and how should I use it? and what does its parameter handle mean? Is it has the same meanning as the parameter handle of...
nRF9160 DK schematic sheet 2 missing pin names for WP and HOLD of nRF91_EXT_MEM in the On-board interface (far right page 2)
could someone post what nRF9160 pins are used...
Hi,
I have written one application with logging disabled to save power.
However, when I tried to debug the code with Ozone, during startup, it raises BusFault exception...
Hi,
I am currently working on generating a dfu over serial uart by testing with the ble_app_blinky example given in the SDK 15.2.0. Currently the ble_app_blinky hex file...
Hi ! Using nRF52840 whith SD140 as central and 6 link count I research :
changing the NRF_SDH_BLE_GAP_EVENT_LENGTH from 6 to 2 does not change "Window size" on CONNECT_REQ...
Hi,
I messed up my SES project and now the debugging session doesn´t start and the debugger does some weird stuff and doesn´t execute my application.
I also tested if...
Hi,
I am using the DFU example given in the SDK15.2.0 to try and update the application on my NRF52840. Currently, I have been able to update the application to run the...
I use many SEGGER_RTT_WriteString and SEGGER_RTT_printf sprinkled throughout my code which was very helpful for debugging and monitoring, however, we're getting close to releasing...
I have attempted to update the firmware on the Nordic Thingy:91 via usb connection to my laptop running CentOS 8, however, finding great difficulty updating the firmware through...
My stm32 (as a master) uses SPI to communicate with nrf52840 (as a slave) When my nrf52840 wants to send data to stm32, it will pull a GPIO to let stm32 generate a GPIO interrupt...
I am using a BL632 DK from Laird, trying to erase the onboard 52832 device. I can connect to the target, but it fails when try erase all.
Results from connect target:
...
Hello,
I am trying to adapt the new Mesh Sensor Model examples in v4.2.0 of the SDK for Mesh to allow sending >1 byte sensor data over the mesh network. I have two nRF52840DK...
Hi
I am using nrf52832-PAC10040, SDK : RF5_SDK_17.0.2 .
USE CASE:I need to make connection between HID keyboard with Central(ble_app_uart_c) . And send/receive data...
I got a nrf52832 custom board to communicate with LIS2DH12 accelerometer by I2C(TWI).
I edited part of the code from "twi_sensor" project in NRF5_SDK version 17.0.
I tried...
Hello,
I have an external flash w25q32 spi nor flash. I tried to communicate with my flash using spi_nor driver code in zephery however it didn't detect the external flash...
I use nRF Connect BLE for Desktop (v.3.6.1) to emulate an app I currently develop.
Using the adveritisement dialog I specify "Complete local name", "UUID 16 bit complete...
