hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Hi,
I have a client/ server question regarding indication values from both the server and the client. What is the message flow?
For example. Can the indication value...
Hi there,
I am implementing the SAADC example into my application whereby I should be able to sample all 8 ADC channels "simultaneously" at a relatively high frequency...
I am trying to change the radio Tx power in nRF5340. I'm using Zephyr HCI RPMsg for the network core. The datasheet says it should support up to 3dBm. However, the Zephyr...
In the soft device documentation (html) the message sequence diagram for Btle Stack Enable calls sd_ble_cfg_set twice with the same set of parameters. Is this a mistake? The...
Hi All,
I am developing a custom BLE profile for my current project and several of my characteristics are write/notify characteristics. I am finding that when I write...
Hi there,
I just started using Embedded Studio (v5.10d on Windows 10, nRF Connect SDK version 1.4) with nRF52840dongle and nRF5340 PDK. Here is what I did
1. Copied...
Hi, I am developing a new project in which I will use NRF52810. I read in the datasheet that it is possible to configure NRF52810 in LDO and DC / DC regulators mode. My application...
Hello:
Looking at the different demos (applications and samples) available for nRF9160, I noticed that some of them generate multiple hex files while others, only few...
Hi,
I have bootloader programmed in nrf52840. Using OTA I programmed one application region but that application stuck after bootup.
Now how to recover from this situation...
Hi,
I have an existing application built on top of the ble_att_mtu_throughput example. I want to send log data over a BLE connection, and I am trying to use the CLI over...
Hello, guys!
We are using nRF52840 with SDK 17.2. In our system, there is a need to configure nRf52840 as SPI slave device and connect it to some other MCU. Naturally, our...
Hello,
I had a problem with the nordic uart service peripheral. We are using an nRF51822 and the S130 software stack. I had a problem with the app_timer.c STATIC_ASSERT...
Hello guys,
I am facing the following problem:
I created a project from zero, using the Nordic Package for SeggerStudios
--> I selected the option A C/C++ executable...
Hi,
Tried enabling POF on while using S140 with the following code:
The board VDD and VDDH are configured to be 3.3V and in the lab, were dropping the voltage to...
