I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
Hi,
for a project I need to perform a DFU Update over BLE. After I prepared the bootloader (generating public and private keys and building it), I prepared the update packet...
Hi, I develop device for custom location service based on BLE. Now I'm working with nRF52 Development kit v1.1.0, nRF52832, SDK v15.0.0.
I have a problem with adding 16bit...
Hi,
I wonder if all Tracedata[n] pins are needed for debug? That would make five IO:s useless for other functions. Or is it possible to use 1-bit mode or something similar...
I wnat to set P0.30 and P0.31 for I2C CLK and SDA. nrf_drv_gpiote_out_config_t out_config = GPIOTE_CONFIG_OUT_SIMPLE(false); err_code = nrf_drv_gpiote_out_init(30, &out_config1...
I set up my nrf52 self board with internal LDO using reference schematics with internal LDO setup.
Im entering the power safe mode using __WFE instruction
Also i did...
1.I used Timer2 Capture function Time Frequency is 1MHz. Picture1 Current counter should be 33330. Picture2 Current counter should be 5000. Picture3 Current counter should...
Hello,
I am having an issue with setting up the event generation timing on the nRF51822. Long story short, I am configuring Timer/Counter 0 to generate an event every 50ms...
Hello,
I am using NRF51 DK for developing an application. I tried running the default SPI example in the SDK 12.3 which uses the spi and spis example. The location of those...
Issue exists in SDK 15.0 and probably many many others...
I noticed that the nrf_log_push parameter is indicating it must be a constant pointer to a mutable character...
I'm attempting to pull the mesh bootloader out of the sdk and put it in its own makefile project, so it can be built separately.
I'm building with `gcc-arm-none-eabi-7-2017...
Hello,
I want to achieve bidirectional data communication between one central and two peripherals. Any my central device should be able to do bi-directional communication...
Hi. I have been looking through the forum to find anything that could answer my problem, but can't seem to find it. I am working a project, where our needs is to use a nrf52...
Hi there ...
In Softdevice S140 v6.1.0 started supporting advertising extension with this macro "BLE_GAP_ADV_SET_DATA_SIZE_EXTENDED_MAX_SUPPORTED" and I follow the migration...
Hi Team,
I am using nrf51822 for my project, i have connected a PIR Sensor and a push button also a LED driver WS2811 .
I am using ble app uart example as i have to control...
