I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Hi,
I wanted to know whether Bluetooth 5.0 will ever be supported on the NRF51 series chips or we need to migrate from NRF51 to NRF52 in order to have Bluetooth 5.0 in...
hi,I have a issue about pairing.
anyone can tell me the process of pairing and binding ,how the event BLE_GAP_EVT_SEC_PARAMS_REQUEST generate;
Do you have same example about...
Hello,
I am developing a board, with nrf51422-qfaa chip. To match the antenna I'm using the BAL-NRF01D3 balun. I currently have problems with antenna not working and I'm...
I am running an appliction with S132 soft device, build on top of SDK 12.0.0. Problem is that the application sometimes stops running for ten seconds, or even more, when Bluetooth...
Hi all,
may be you can advice me on a solution.
I need to be able to wake up a system when one of the pins shows more than 1v and I also need to wake up system when...
Hi,
I'm using ble_app_multilink_central to connect different device.In the example, it can connect to the lbs service. If I want it connect the uart service,such as ble_app_uart...
Hi Nordic,
we need to modify bootloader code base on your dfu example. Now We meet a problem that we can't program it by clicking icon "Load" on keil comile project. report...
I am having problem to download SDK NRF51 12.0 example firmware onto Redbearlab BLE Nano nrf51822. The compilation and build is fine. It is shown as
Erased Failed!
Error...
I have a custom board with an nRF51822, running the ble_app_hrs from the 12.1.0 SDK with softdevice s130, using the internal RC clock in a custom_board.h as follows:
#define...
I'm learning about the nRF52 series and so far love everything I see, especially the SDK. But I just got to the point where I'd like to generate precisely timed output, and...
Hello Nordic Team,
As I'm worrying about the max payload lengh that I can notify using soft device s130.1.0.0 on nrf51822 (256 Kb Flash/ 16KB RAM, SDK10), I thought about...
Hi,
I'm porting our project from sdk10 to sdk12 with SD S132 V3.0.0. I cannot find a way to reset the device in app and boot in bootloader in order to do a OTA update....
I have a working custom DFU bootloader based on the official bootloader from the SDK 8.1.0.
Updating the normal application code works without any problem.
Now I want to...
Hello all,
I try to trigger two events with two different periods, the first at 200ms, the second at 300ms. When I set the same period for the compared value, it works...
Hello,
I am tring to do a Bootloader update OTA using the bootlader DFU Dual Bank. Application update OTA is working fine while it is not the case for Bootloader update...
