I'm analyzing app_timer scheduling code..
I have an question about list_insertation_handler function in SWI0_ISR
I think if ( (p_timer->ticks_at_start - m_ticks_latest...
I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Im trying to provide DTM functionality for certifications tests. I can't setup an UART interface, I found the below code which tries to use DTM without UART. it uses channel...
Hello,
I've read a lot about trouble people had when they used bluetooth and flashed the rom without using the propper softdevice APIs.
What is the issue with concurent...
Good morning.
I ´m working with nrf51-dk, sdk 9.0.0 and softdevice 110.
I have done a proyect without softdevice, only uart and master spi (mode 0) and works perfect...
Hi, I flashed the Proximity Application to nrd51822,with s110_nrf51822_6.0.0-5.beta.
the chip run right, and I used the NRF Master Control Panel, when I write data 0X02 to...
Dear all,
I have tried using a setting a break point in main() of my program. Without running the softdevice, it is fine to pause in the break point and continue to run...
Hi,
I am developing a product using nrf51822. While pcb designing I am getting a clearance error. Please let me know how to resolve it. All the dimensions are 8mil in clearance...
Hi,
I am editing my question:
I have seen some strange behaviuor I could not explain. In order to test it I have made the next test program:
I am using the application...
Hi,
I recently bought the nrf 51 development kit. Before implementing a BLE application on the board I wanted to start with a simple application of blinking a LED by pressing...
1.I have a nRF51_DK and nrf51822(waveshare core51822)
2.Keil 5.18v and all of the needed software were Installed
3.s130 1.0.0 or 2.0.0 and sdk9.0 or 10.0 were used ...
Hi Nordic Dev Zone, Ray Kampmeier here.
I'm building Direct Test Mode (DTM) into a production application that uses the 110 soft device. Unlike the provided Nordic examples...
Is there any way to integrate SoftDevice with entire project so I can get one hex from build? I am new to CrossWorks and nRF52 and I am developing BLE device. After getting...
I want to do firmware update over the air in a STM32F4xx microcontroller which is connected with nRF51822 chip via UART (TX, RX, CTS, DTR) and BOOT pins. ST microcontroller...
Hi
I can get the current time from the server using the time service characteristic. Which function should I use to set the RTC clock on the nrf 51 to the current time...
