Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Hello guys,
I was refreshing BLE concepts by doing the BLE Fundamentals once again and I have faced some trouble with the nRF5340 dk on Lesson 2. I have built the application...
Hi,
we have nRF54H20DK (SoC rev. "C"). connected to MAX77655 via I2C (SCL ~ P1.0, SDA ~ P1.4 according to I2C restriction).
I am trying to test i2c131 for reading/writing...
Hello,
We are using DFU target library with MCUboot (Connect SDK v2.9.0):
And we are getting assertion fail on first dfu_target_offset_get() call after FW update:
...
Please confirm whether the "sample app nrf5340_audio" in "v2.8.0" supports "GAIN control" in "SPI+GPIO mode". the method to enable "GAIN control" in "SPI+GPIO mode" if the...
Hi Nrodic，
Does NRF5340 have an example code for QSPI driving uLED display peripherals (for example, I need to drive this display chip: JBD013VGA， As per the attached...
I'm following along with the Nordic Academy tutorial for v2.7.0-v2.9.0. I made the recommended modifications to my v2.9.0 project with an nRF54L15-DK target:
Create sysbuild...
Hello! I am developing my own BLE solution where I have the different attributes in my service and I am connecting two different nrf52840, one to act as a GATTClient and one...
I am attempting to do a simple read from the FEM on the nrf21540-DK board. I should be able to use the zephyr driver with spi3 (or fem_spi) to do a simple read/write from...
I'm writing a client/central application connecting to a peripheral, discovering a service, and then wishing to enable notifications from a specific characteristic.
Once...
Hi,
I am trying to write a file to the FAT file system on nRF7002 board.
Here is what I have tried:
in proj.conf:
ONFIG_FILE_SYSTEM =y
CONFIG_FLASH =y
CONFIG_FLASH_MAP...
Hi,
we have nRF54L15DK (rev. 0.9.1). connected to MAX77655 via I2C.
I am trying to test i2c21 and i2c22 for writing data. I have tested it on different SCK and SDA on...
I'm following the instructions to build a co-processor using the nRF52840 dongle, on Ubuntu 22.04: https://docs.nordicsemi.com/bundle/ncs-2.9.0/page/nrf/protocols/thread/tools...
I have tried to debug my nordic5340 with VS code and it fails to load the code, although I'm able to flash the code using vs code.
when trying to track the problem using...
Hello,
I've come back to an existing project after a reboot of my computer and I'm now getting the error when I execute a build:
ImportError: Module use of python39...
https://academy.nordicsemi.com/courses/nrf-connect-sdk-fundamentals/lessons/lesson-6-serial-com-i2c/quizzes/lesson-6-quiz/
I think "i2c_read()" can only be used by I2C master...
